background image

 

TROUBLESHOOTING 

Before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description 
of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local dealership. 
 

State of abnormality 

Probable cause (malfunction) 

Remedy 

Failure to operate primer pump 

Push 7 to 10 times. 

Low pulling speed of starter rope 

Pull strongly. 

Lack of fuel 

Feed fuel. 

Clogged fuel filter 

Clean 

Broken fuel tube 

Straighten fuel tube 

Deteriorated fuel 

 

Deteriorated fuel makes starting more difficult. 
Replace with new one. (Recommended 
replacement: 1 month) 

Excessive suction of fuel 

 

 

 

 

Set throttle lever from medium speed to high 
speed, and pull starter handle until engine 
starts.  

If engine will not start still, remove spark plug, 
make electrode dry, and reassemble them as 
they originally are. Then, start as specified. 

Detached plug cap 

Attach securely 

Contaminated spark plug 

Clean 

Abnormal clearance of spark plug 

Adjust clearance 

Other abnormality of spark plug 

Replace 

Abnormal carburetor 

Make request for inspection and maintenance.

Starter rope cannot be pulled 

Make request for inspection and maintenance 

Engine does not start 

Abnormal drive system 

Make request for inspection and maintenance 

Insufficient warm-up 

Perform warm-up operation 

Choke lever is set to “CLOSE” although engine 
is warmed up 

Set to “CLOSE” 

Clogged fuel filter 

Clean 

Contaminated or clogged air cleaner 

Clean 

Abnormal carburetor 

Make request for inspection and maintenance 

Abnormal drive system 

Make request for inspection and maintenance 

Detached throttle wire 

Attach securely 

Engine stops soon 
Engine speed does not increase 

Abnormal drive system 

Make request for inspection and maintenance 

Detached connector 

Attach securely 

Abnormal electric system 

Make request for inspection and maintenance.

Engine does not stop. 

 

 

 

 

 

When the engine does not start after warm-up operation: 
If there is no abnormality found for the check items, open the throttle by about 1/3 and start the engine. 

 

 

 

 

 

Run engine at idling, and set choke 
lever to CLOSE. 

18

Summary of Contents for BHX2500


























Reviews: