background image

 

FEDERAL EMISSION COMPONENT DEFECT WARRANTY 

 
EMISSION COMPONENT DEFECT WARRANTY COVERAGE - This emission warranty is 
applicable in all States, except the State of California 
 
Makita U.S.A., Inc., La Mirada, California, (herein "MAKITA") warrant to the initial retail 
purchaser and each subsequent owner, that this utility equipment engine (herein "engine" ) 
was designed, built, and equipped to conform at the time of initial sale to all applicable 
regulations of the U.S. Environmental Protection Agency (EPA), and that the engine is free 
of defects in materials and workmanship which would cause this engine to fail to conform 
with EPA regulations during its warranty period. 
 
 For the components listed under PARTS COVERED, Makita Factory Service Center or 
service center authorized by Makita will, at no cost to you, make the necessary diagnosis, 
repair, or replacement necessary to ensure that the engine complies with applicable U.S. 
EPA regulations. 
 
 

EMISSION COMPONENT DEFECT WARRANTY PERIOD 

 
The warranty period for this engine begins on the date of sale to the initial purchaser and 
continues for a period of 2 years. 
 
 

PARTS COVERED 

 
Listed below are the parts covered by the Emission Component Defect Warranty.    Some of 
the parts listed below may require scheduled maintenance and are warranted up to the first 
scheduled replacement point for that part. 
 
1)  Fuel Metering System 
    (i)  Carburetor and internal parts 
    (ii)  Fuel filter, if applicable 
    (iii) Throttle stopper, if applicable 
    (iv) Choke System, if applicable 

2)  Air Induction System 
  (i)  Air cleaner plate 
  (ii)  Air cleaner case 
  (iii) Air cleaner element 

3) Ignition 

System 

  (i)  Spark plug 
  (ii)  Flywheel Magneto 
  (iii) Ignition Coil 

4)  Miscellaneous Items Used in Above Systems 
    (i)  Fuel hoses. clamps and sealing gaskets 
 

24

Summary of Contents for BHX2500


























Reviews: