background image

7

OPERATION

WARNING:

It should never be necessary to force the tool. The weight of the tool
applies adequate pressure. Forcing and excessive pressure could cause
dangerous wheel breakage.

ALWAYS replace wheel if tool is dropped while grinding.

NEVER bang or hit grinding disc or wheel onto work.

Avoid bouncing and snagging the wheel, especially when working
corners, sharp edges etc. This can cause loss of control and kickback.

NEVER use tool with wood cutting blades and other sawblades. Such
blades when used on a grinder frequently kick and cause loss of control
leading to personal injury.

CAUTION:

After operation, always switch off the tool and wait until the wheel has
come to a complete stop before putting the tool down.

Grinding and sanding operation

ALWAYS hold the tool firmly with one hand on housing and the other on the
side handle. Turn the tool on and then apply the wheel or disc to the work-
piece.
In general, keep the edge of the wheel or disc at an angle of about 15 degrees
to the workpiece surface.
During the break-in period with a new wheel, do not work the grinder in the B
direction or it will cut into the workpiece. Once the edge of the wheel has been
rounded off by use, the wheel may be worked in both A and B direction.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and unplugged before
attempting to perform inspection or maintenance.

The tool and its air vents have to be kept clean. Regularly clean the tool’s air
vents or whenever the vents start to become obstructed.

To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspec-
tion and replacement, any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always using Makita
replacement parts.

15

A

B

005831

1. Exhaust vent

2. Inhalation vent

1

2

005809

Summary of Contents for 9555NB













Reviews: