background image

6

To install the drill chuck, screw it onto the angle head firmly
(do not overtighten) and replace the screw removed earlier
from the drill chuck. It screws in counterclockwise.
Fit the sleeve onto the hex end of the drill spindle and then
slip on the joint, tightening the joint bolt (A) with the wrench.

Slide the angle head into the joint, rotate the angle head to
the desired drilling position and tighten the joint bolt (B) with
the wrench.

CAUTION:

To avoid damage to the drill and the angle head, do not
tighten the joint bolts without the joint properly positioned
on the drill and on the angle head.

Installing or removing drill bit

To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each of
the three holes and tighten clockwise. Be sure to tighten all
three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in just
one hole, then loosen the chuck by hand.

OPERATION

Drilling operation

Drilling in wood

When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the bit into the workpiece.

1. Angle head

2. Joint

3. Joint bolt(A)

4. Sleeve

1

2

3

4

003064

1. Joint bolt(B)

1

003065

1. Chuck key

1

003552

Summary of Contents for 6300LR













Reviews: