6
ENG901-1
•
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
•
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
•
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
•
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-12
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Trimmer
Model No./ Type: 3710
are of series production and
Conforms to the following European Directives:
98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
30.01.2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
GEA010-1
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for
future reference.
GEB019-2
TRIMMER SAFETY WARNINGS
1.
Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord.
Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock
the operator.
2.
Use clamps or another practical way to secure
and support the workpiece to a stable
platform.
Holding the work by hand or against
your body leaves it unstable and may lead to loss
of control.
3.
Wear hearing protection during extended
period of operation.
4.
Handle the bits very carefully.
5.
Check the bit carefully for cracks or damage
before operation. Replace cracked or
damaged bit immediately.
6.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
7.
Hold the tool firmly.
8.
Keep hands away from rotating parts.
9.
Make sure the bit is not contacting the
workpiece before the switch is turned on.
10.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate improperly
installed bit.
11.
Be careful of the bit rotating direction and the
feed direction.
12.
Do not leave the tool running. Operate the tool
only when hand-held.
13.
Always switch off and wait for the bit to come
to a complete stop before removing the tool
from workpiece.
14.
Do not touch the bit immediately after
operation; it may be extremely hot and could
burn your skin.
15.
Do not smear the tool base carelessly with
thinner, gasoline, oil or the like. They may
cause cracks in the tool base.
16.
Draw attention to the need to use cutters of
the correct shank diameter and which are
suitable for the speed of the tool.
Summary of Contents for 3710
