background image

Important

Do not leave the machine switched on or unattended when not in use.

Make sure to close the shut off valve of the water connection and to switch off
the electric main switch or to disconnect the power plug when the machine is
not in use
.

If you will not be using the machine for an extended period of time, we
recommend emptying the machine by letting the water run out via the brew
group.

6. First use

Read the following instructions carefully prior to operating the machine

Important
Prior to starting the machine, check if:

The steam and hot water valves are closed.

The machine is switched off.

The power cord is disconnected.

The drip tray is inserted accurately.

The machine is placed on a water-resistant surface.

Now you can continue to start up your machine.

6.1 Water tank machine or machine in use with water tank

1. Remove the cup tray. Take out the water tank and rinse it thoroughly.
2. Fill the water tank (2 liter) with fresh drinking water (preferably descaled), place it back into

the water tank guides and put the cup tray back to its position.

3. Connect the machine to an appropriate power outlet through the power supply cable.
4. Turn the power switch to position “I”. The machine is now on.
5. The green signal lamp lights up.
6. The pump will fill the boiler of the machine with fresh water.
7. As soon as the boiler is filled, the pump will stop. As soon as the fresh water falls below a

certain level in the water tank, the machine switches off and the red signal lamp turns on. To
reset to normal working conditions, turn the main switch OFF first. Refill with fresh water and
turn the main switch in position “I”. The boiler will start to refill, the red signal will turn off and
the machine will heat up automatically.

8. A large amount of water is required to fill the boiler for the first time, so the water tank will

have to be refilled with fresh water.

9. Wait until the boiler pressure gauge indicates approx. 1.01.3 bar or a temperature of 120° C

248°F has been reached.

10. Move the group lever into the upper position and dispense approx. 500 ml of water. This way,

the heat exchanger will be filled with water and the circulation of the water in the
thermosyphon system begins.

11. Move the group lever into the lower position. Refill the water tank.
12. The machine is now ready for use.

Page 13

Summary of Contents for S7 PRO-PID





















Reviews: