EN 54-16 certified PA/VA System SERIES
5 6 , c h e m i n d e l a Fl a m b è re · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r
User manual V1.1
5 6 , c h e m i n d e l a Fl a m b è re · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r
Usermanual V1.1
19
18
SERIES EN 54-16 certified PA/VA System
Page
18
sur
51
Ϯ͘ϰ͘ϱ
POWER SUPPLY
Every equipment in the EXEO series has double redundant power supply.
ĂͿ
AC LINE VOLTAGE SELECTOR
The equipment has an AC line voltage selector 230V / 115V, by default in the 230V position. Check
the local line voltage to configure the selector.
Marking Description
Type
Signals Activation
AC line voltage selector
Config
NA 230V /115V
Table 9: Line Voltage Selector
ďͿ
MAIN POWER SUPPLY INPUT
The unit has an IEC 60320/C14 input connector for
connection to the main power supply.
The connection is made using IEC power cord to E + F
Male 60320/C13 plug supplied with the equipment.
Marking Description
Type
Signals Activation
Main power supply input
Input
L N G 230V /115V 50/60Hz
(according to selector)
Table 10: Main Power Supply Input
ĐͿ
EMERGENCY POWER SUPPLY FUSE:
The unit has room for a fuse to protect the overload of the emergency
power supply input. The fuse will be cylindrical with a 6x32mm glass, and
the maximum intensity specified in the technical specifications of the
equipment (see section 46). To access the fuse, turn the fuse holder a
quarter turn counterclockwise using a flat blade screwdriver.
Picture 18: AC Line voltage selector
Picture 19: Main power supply input
Picture 20: Emergency Power Supply
Fuse.
Page
19
sur
51
ĚͿ
EMERGENCY POWER SUPPLY INPUT:
The unit has an input for emergency power supply. The emergency power
is continuous and 24V nominal value. It will be supplied independently,
consisting of a battery system and charger according to EN54-4. The input
consists of a two poles + and - connector to be connected to the positive and
negative poles of the battery system. For more information about the
connection of the emergency power supply system, see section 7.
The connection is made by 2 pin female euro block connector and 7,62 mm
(supplied with the unit). The wire size range for each pole of this connector is
0.2 → 6mm2 (24 → 8 AWG).
Marking Description
Type
Signals Activation
20-28V Emergency Power Supply Input
Input
+
-
20 - 28V DC
Maximum Power: see technical data
(Chapter 46)
Table 11: Emergency Supply Input
Ϯ͘ϰ͘ϲ
SPEAKER'S LINES
ĂͿ
SPARE CHANNELS INPUT
The equipment has 8 inputs back-up amplifier
channels per each internal amplifier. Each connection has
two terminals + and – where the redundant amplifier
output will be connected. The redundant amplifier must
be a 100V line public address amplifier with a minimum
power equal to the nominal channel amplification power
of the equipment. For more information about the
connection of back-up amplifier, see chapter 4.5.
The connection is made with a 2-pin female euro block
connector and pitch 5.08 mm (supplied with the unit). The
wire size range for each pole of this connector is: 0.5 →
2.5 mm2 (22 → 12 AWG).
Marking Description
Type
Signal Activation
SPARE CH
INPUTS
X
Input amplification channel
corresponding to the channel
reservation amplification equipment
X
Input
+
-
NA
Table 12: Spare Channel Inputs
ďͿ
SPEAKER LINE OUTPUT
The equipment has between 4 and 8 amplification channels, each channel has two speaker line
outputs marked as A and B. The rated power of the amplifier channel is divided between both output
lines. For more information about the connection of the speaker lines see chapter 4.6. Each line
connection has two + and - terminals for connecting speakers to 100V or low-impedance depending on
the model.
Picture 21:
Emergency Power Supply Input
Picture 22: Back up amplifiers inputs
