Major 1150 Slurry Vac Operator'S Manual & Parts List Download Page 22

Page: 22 / 89

www.major-equipment.com

Top Fill

Keep bystanders clear when operating top fill as there is a danger of entrapment.

Top fill shown fully open

NOTE: Top fill is pressure tested and adjustment is set before leaving factory.

1. Connect Top Fill hydraulic hoses to the tractor.

Ensure top fill is held closed by pressure bar (hydraulics) before undoing the toggle clamps.

3. The lid will now open and close hydraulically.

If air is leaking from around the seal, check seal and ring for damage. If pressure bar requires adjustment then slacken

adjuster nuts below bar ¼ turn at a time. Ensure adjustment is equal.

Over adjustment can damage the seal ring and stress the top fill.

Water Spreader

Operation ( Do not operate water spreader without guarding.)

1. Pressurise tanker.

2. Start Water Spinner motor

3. Open the 6” gate valve.

4. Water spreader disk speed can be varied by the

tap located on the tractor feed coupling.

IMPORTANT

Hydraulic hoses must be correctly connected. The ¼” hose is

the feed hose and the ½” hose is the return line. The Return

line must return. Damage to the hydraulic motor can occur if

hoses are connected incorrectly.

Summary of Contents for 1150 Slurry Vac


























































































Search results

Summary of Contents for 1150 Slurry Vac

Reviews:

Brands by name

Popular brands

Major 1150 Slurry Vac, Operator'S Manual & Parts List

Search results

Summary of Contents for 1150 Slurry Vac

Reviews:

Brands by name

Popular brands