background image

4

1. SAFETY WARNINGS

1.1. International Safety Symbols

Warning of a potential danger, comply with instruction manual.

Caution! Dangerous voltage. Danger of electrical shock.

Double insulation.

1.2. Safety Notes

• Reference. Please use utmost attention.
• Do not exceed the maximum allowable input range of any function
• Be sure to read the instructions carefully before using and check that the 

battery is adequate. Do not remove the voltage detector without 
authorization from professional technicians. If the voltage detector is not 
used for a long time, take out the battery and store it in a dry tool box.

1.3. Safety Advices

• Depending on the internal impedance of the voltage detector there will be 

a different capability of indicating the presence or absence of operating 
voltage in case of the presence of interference voltage.

• A voltage detector of relatively low internal impedance, compared to the 

reference value of 100kΩ, will not indicate all interference voltages having 
an original voltage value above the ELV level. When in contact with the 
parts to be tested, the voltage detector may discharge temporarily the 
interference voltage to a level below the ELV, but it will be back to the 
original value when the voltage detector is removed.

• When the indication "voltage present" does not appear, it is highly 

recommended installing earthing equipment before work.

• A voltage detector of relatively high internal impedance, compared to the 

reference value of 100kΩ, may not permit to clearly indicate the absence 
of operating voltage in case of presence of interference voltage.

• When the indication "voltage present" appears on a part that is expected 

to be disconnected of the installation, it is highly recommended 
confirming by another means (e.g. use of an adequate voltage detector, 
visual check of the disconnecting point of the electric circuit, etc.) that 
there is no operating voltage on the part to be tested and to conclude 
that the voltage indicated by the voltage detector is an interference 
voltage.

• A voltage detector declaring two values of internal impedance has passed 

a performance test of managing interference voltages and is (within 

 

 

Summary of Contents for MT476

















Reviews: