background image

15

Majestic  •  PEARL36STIN, PEARL36PRIN Owner’s Manual  •  2478-981 Rev. C  •  6/18

 

Appliance ON/OFF:

A wall control, thermostat or remote control may be used 
to control the ON/OFF function of the appliance. Follow 
instructions included with the installed control.

Optional Fan Kit 

If desired, a fan kit may be added.  Contact your dealer 

to order the correct fan kit.  Detailed instructions are in

-

cluded with the fan kit.

DANGER

DANGER

       

-  Wait five (5) minutes to allow possible     

 

          accumulated gas to clear. 

 
       -  Set the IFT-ECM 3-position selector switch to ON  
          or IFT-REM position.  Module will beep once and  

          flash a three GREEN LED code on successful 

 

          startup. 

 
       -  If placed in ON position, the appliance will ignite  
          normally if the error condition was corrected. 

 
       -  If placed in IFT-REM position, use the paired IFT-   
          RC400, IFT-RC150 or wired wall switch to start  
          the appliance; appliance will ignite normally if the 
          error condition was corrected.

      -  If the IFT-ECM re-enters the lock-out condition 

 

         after these steps, call your dealer for service.

Summary of Contents for PEARL II Series





























Reviews: