background image

Majestic  •  JADE32IN, JADE42IN, JADE42IL Owner’s Manual   •  2491-987 Rev. F  •  9/18

 

6

B.  Glass Specifications

Hearth & Home Technologies appliances manufactured 

with tempered glass may be installed in hazardous lo-

cations  such  as  bathtub  enclosures  as  defined  by  the 

Consumer Product Safety Commission (CPSC). The 

tempered glass has been tested and certified to the re

-

quirements of 

ANSI Z97.1

 and 

CPSC 16 CFR 1202 

(Safety  Glazing  Certification  Council 

SGCC# 1595

 and 

1597

. Architectural Testing, Inc. Reports 

02-31919.01

 

and 

02-31917.01

).

This statement is in compliance with 

CPSC 16 CFR Sec-

tion 1201.5 

“Certification  and  labeling  requirements” 

which refers to 

15 

U.S. Code 

(USC) 2063 

stating “…Such 

certificate shall accompany the product or shall otherwise 

be furnished to any distributor or retailer to whom the 

product is delivered.”
Some local building codes require the use of tempered 

glass  with  permanent  marking  in  such  locations.  Glass 

meeting this requirement is available from the factory. 

Please contact your dealer or distributor to order.

C.  BTU Specifications

A.  Appliance Certification

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.  

This appliance is tested and approved as either supplemen-

tal room heat or as a decorative appliance.  It should not be 

factored as primary heat in residential heating calculations.

NOTICE: 

This installation must conform with local codes. 

In the absence of local codes you must comply with the 

National Fuel Gas Code, ANSI Z223.1-latest edition in 

the U.S.A. and the CAN/CGA B149 Installation Codes in 

Canada.

Product Specific Information 

 

This product is listed to ANSI standards for “Vented Gas 

Fireplace Heaters” and applicable sections of “Gas Burn-

ing Heating Appliances for Manufactured Homes and 

Recreational Vehicles”, and “Gas Fired Appliances for 

Use at High Altitudes”.

Installation and service of this appliance should be performed by 

qualified personnel. Hearth & Home Technologies recommends 

HHT Factory Trained or NFI certified professionals.

MODELS:

  JADE32IN, JADE42IN, JADE42IL 

LABORATORY:  

Underwriters Laboratories, Inc. (UL)

TYPE:  

Direct Vent Heater

STANDARD:

 ANSI Z21.88-2017  •  CSA 2.33-2017

Models

(U.S. or Canada)

Maximum

Input BTU/h

Minimum

Input BTU/h

Orifice

Size 

(DMS)

JADE42IN 

(NG)

(0-2000 FT)

25,250

17,500

#42

JADE42IL 

(PROPANE)

(0-2000 FT

23,500

17,500

.057

JADE32IN

(NG)

(0-2000 FT)

19,000

13,250

#45

JADE32IN

(PROPANE)

(0-2000 FT)

16,500

12,750

1.25 

mm

Summary of Contents for JADE42IN

































Reviews: