Majestic DBDV36PLATIN Page 44 Installation Manual Download

Page: 44 / 74

Majestic • DBDV36PLATIN, DBDV36PLATIL, DBDV42PLATIN, DBDV42PLATIL Installation Manual • 2454-980 Rev. F • 5/17

A. General Information

WARNING! Risk of Shock or Explosion! DO NOT

wire

110-120 VAC to the valve or to the appliance wall switch.

Incorrect wiring will damage controls.

NOTICE:

This appliance must be electrically wired

and grounded in accordance with local codes or, in the

absence of local codes, with

National Electric Code

ANSI/NFPA 70-latest edition

or the

Canadian Electric

Code CSA C22.1.

• Wire the appliance junction box to unswitched 110-

120 VAC. This is required for proper operation of the

appliance.

• A 110-120 VAC circuit for this product must be protected

with ground-fault circuit-interrupter protection, in

compliance with the applicable electrical codes, when

it is installed in locations such as in bathrooms or near

sinks.

• Low voltage and 110-120 VAC voltage cannot be shared

within the same wall box.

Accessories Requirements

• This appliance may be used with a wall switch, wall

mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved

accessories should be done now to avoid reconstruction.

Follow instructions that come with those accessories.
• Hearth & Home Technologies recommends that Intel

liFire

Plus wireless controls be used for their features

and functionality with the IntelliFire

Plus ignition sys-

tem

Electrical Information

Figure 8.1 Junction Box Detail

NOTICE: DO NOT

wire

110-120 VAC to wall switch.

Junction Box Installation

If the box is being wired from the

INSIDE

of the appliance:

• Remove the screw attaching the junction box/receptacle

to the outer shell, rotate the junction box inward to dis

engage it from the outer shell (see Figure 8.1).

• Pull the electrical wires from outside the appliance through

the opening into the valve compartment and secure wires

with a Romex connector. See Figure 8.1.

• Make all necessary wire connections to the junction box/

receptacle and reattach the junction box/receptacle to

the outer shell.

Electrical Service and Repair

WARNING! Risk of Shock!

Label all wires prior to dis-

connection when servicing controls. Wiring errors could

cause improper and dangerous operation. Verify proper

operation after servicing.

WARNING! Risk of Shock!

Replace damaged wire with

type 105º C rated wire. Wire must have high temperature

insulation.

14/2WG

Romex

Connector

(Not Provided)

WHT

BLK

GRN wire

inside box

Copper

ground attached

to GRN screw with

GRN wire

Summary of Contents for DBDV36PLATIN











































































Search results

Summary of Contents for DBDV36PLATIN

Reviews:

Related manuals for DBDV36PLATIN

Brands by name

Popular brands

Majestic DBDV36PLATIN, Installation Manual

Search results

Summary of Contents for DBDV36PLATIN

Reviews:

Related manuals for DBDV36PLATIN

Brands by name

Popular brands