background image

6

NV360/580 Series 

20003565

Gas Line Installation

When purging gas line the front glass must 
be removed.

The gas pipeline can be brought in through the right 
side of the appliance. Knockouts are provided at conve-
nient locations to allow for the gas pipe installation and 
testing of any gas connection.  
The gas line connection can be made with properly 
tinned 3/8” copper tubing, 1/2” rigid pipe or an approved 
flex connector. Since some municipalities have  addi-
tional local codes, it is always best to consult your local 
authority and the 

CSA-B149.1

 installation codes.

For USA installations consult the current National Fuel 
Gas Code, 

ANSI Z223.1/NFPA 54

.

Always check for gas leaks with a mild 
soap and water solution applied with a 
brush no larger than 1” (25 mm). Never 
apply soap and water solution with a spray 

bottle. Do not use an open flame for leak 
testing.

Framing and Finishing

Check appliance to make sure it is levelled 
and properly positioned.

1.  Choose unit location.
2.  Nailing flanges are supplied with the fireplace (found 

on the fireplace hearth). To level the box and secure 
it firmly in place, remove the nailing flanges from 
the hearth and install at the sides of the firebox as 
shown in Figure 3.

3.  Screw through the slotted holes in the drywall strip 

and into pre-drilled holes in fireplace side. Measure 
from face of fireplace to the face of the drywall strip 
to confirm the final depth.

Finishing

Noncombustible materials such as brick and tile can 
be extended over the face of the unit (Do not cover the 
glass door or grille). If a trim kit is to be installed, brick 
and tile will have to be installed flush with the side of 
this appliance.

Gas Specifications

 

 

 

 

Max. 

Min.

 

Model 

Fuel 

Gas Control 

Input 

Input

  NV360RN  Natural 

Millivolt Hi/Lo 

33,500  23,500

  NV360RP  Propane 

Millivolt Hi/Lo 

33,500  23,700

  NV580RN  Natural 

Millivolt Hi/Lo 

45,000  31,500

  NV580RP  Propane 

Millivolt Hi/Lo 

45,000  31,900

NV360 / NV580

Certified to

ANSI Z21.50b-2002 / CSA 2.22b-2002 

Vented Gas Fireplace

High Elevations

Input ratings are shown in BTU per hour and are 
certified without deration for elevations up to 
4,500 feet (1,370m) above sea level.
For elevations above 4,500 feet (1,370m) in USA, 
installations must be in accordance with the 
current ANSI Z223.1/NFPA 54 and/or local codes 
having jurisdiction.
In Canada, please consult provincial and/or local 
authorities having jurisdiction for installations at 
elevations above 4,500 feet (1,370m).

  Minimum Inlet Pressure 

5.5" w.c. 

11" w.c.

  Maximum Inlet Pressure  14.0" w.c.  14.0" w.c.
  Manifold Pressure 

3.5" w.c. 

11" w.c.

Natural

LP

Gas Inlet & Manifold Pressures

Units: H31A00, H31B00, I31A00, I31B00

FP1023

side nailing flange

1/27/00  djt

C

A

B

Adjustable Drywall Strip 

(Nailing Flanges)

 

Screw 

Drywall

  Position 

Depths

 

1/2" / 13 mm

 

5/8" / 16 mm

 

3/4" / 19 mm

Adjustable

1/2", 5/8" & 3/4" 

Spacing

FP1023

Fig. 3

  Nailing flanges.

Air Shutter Setting

 

Model 

Front 

Rear 

 

NV360RN 

closed 

closed

  NV360RP 

open 

open

  NV580RN 

closed 

closed

  NV580RP 

open 

open

Summary of Contents for NV360 Series





























Reviews: