background image

14

Majestic  •  MDVI30IN, MDVI35IN Owner’s Manual  •  2205-981 Rev. D  •  8/16  

C.  Maintenance Tasks - Quali

fi

 ed Service 

Technician

The

 

following tasks must be performed by a quali

fi

 ed ser-

vice technician.

Gasket Seal and Glass Assembly Inspection

Frequency: 

Annually

By:  

Quali

fi

 ed Service Technician

Tools needed:

 Protective gloves, drop cloth and a stable 

work surface.
•  Inspect gasket seal and its condition.
• Inspect 

fi

 xed glass assembly for scratches and nicks that 

can lead to breakage when exposed to heat. 

• Con

fi

 rm there is no damage to glass or glass frame. 

Replace as necessary.

• Verify that 

fi

 xed glass assembly is properly retained and 

attachment components are intact and not damaged. 
Replace as necessary. 

Logs

Frequency: 

Annually

By:  

Quali

fi

 ed Service Technician

Tools needed:

 Protective gloves.

•  Inspect for damaged or missing logs.  Replace as neces-

sary.  Refer to Installation manual for log placement instruc-
tions.

•  Verify correct log placement and no 

fl

 ame impingement 

causing sooting.  Correct as necessary.

Control Compartment and Firebox Top

Frequency: 

Annually

By:  

Quali

fi

 ed Service Technician

Tools needed:

 Protective gloves, vacuum cleaner, dust 

cloths
•  Vacuum and wipe out dust, cobwebs, debris or pet hair.  

Use caution when cleaning these areas.  Screw tips that 
have penetrated the sheet metal are sharp and should 
be avoided.

•  Remove all foreign objects.
•  Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: 

Annually

By:  

Quali

fi

 ed Service Technician

Tools needed:

 Protective gloves, vacuum cleaner, whisk 

broom, 

fl

 ashlight, voltmeter, indexed drill bit set, and a 

manometer.
•  Verify burner is properly secured and aligned with pilot 

or igniter.

•  Clean off burner top, inspect for plugged ports, corrosion 

or deterioration.  Replace burner if necessary.

•  Replace Glowing embers with new dime-size pieces.  

DO NOT

 block ports or obstruct lighting paths. Refer 

to appliance installation manual for proper ember 
placement.

•  Verify batteries have been removed from battery back-

up IPI systems to prevent premature battery failure or 
leaking.

•  Check for smooth lighting and ignition carryover to all 

ports. Verify that there is no ignition delay.

•  Inspect for lifting or other 

fl

 ame problems.

•  Verify air shutter setting is correct.  See Installation 

Manual for required air shutter setting.  Verify air shutter 
is clear of dust and debris. 

• Inspect ori

fi

 ce for soot, dirt and corrosion. Verify ori

fi

 ce 

size is correct.  See Service Parts List  for proper ori

fi

 ce 

sizing.

•  Verify manifold and inlet pressures. Adjust regulator as 

required.

• Inspect pilot 

fl

 ame pattern and strength. See Figure 4.2 

for proper pilot 

fl

 ame pattern. Clean or replace ori

fi

 ce 

spud as necessary.

• Inspect

 

IPI 

fl

 ame sensing rod for soot, corrosion and 

deterioration. Polish with 

fi

 ne steel wool or replace as 

required.

•  Verify that there is not a short in 

fl

 ame sense circuit 

by checking continuity between pilot hood and 

fl

 ame 

sensing rod. Replace pilot as necessary. 

Figure 4.2  IPI Pilot Flame Patterns

Summary of Contents for MDVI30IN
























Reviews: