manualshive.com logo in svg

MAHLE FluidPRO ATX-3 PLUS BOOST, Operation Manual, Page: 17 / 23

Share
Download
MAHLE FluidPRO ATX-3 PLUS BOOST Operation Manual Download Page 17

Page 16 

CALIBRATION OF LOAD CELLS

 

The ATX-3 PLUS BOOST has two tanks, each mounted on a load cell. One tank is for new fluid and one is for used 
fluid. Each tank is 

permanently bolted

    to a load cell platform which cannot be removed from the unit. The 

calibration procedure below must be performed for both 

both 

both 

both load cells. 

Never calibrate only one load cell as an imbalance may occur and the ATX-3 PLUS BOOST will 
not operate correctly.

    

1.  Remove the rear panel. 
2.  Place end of 

8 ft black hose (left side of ATX-3 PLUS BOOST)

    in bulk used fluid container. Place any adapter 

onto coupler on end of hose. 

3.  Press and hold 

4 LITER

    and 

20 LITER

    buttons until a long beep is heard. 

4.  Select which load cell is to be calibrated. 

a) 

Press 

-1/2 LITER

    to calibrate the used fluid load cell. 

REMOVE USED FLUID

    will be flashing

 

throughout the remaining steps. A short beep will be heard. 

b) 

Press 

+1/2 LITER

    to calibrate the new fluid load cell. 

ADD NEW FLUID

    will be flashing throughout the 

remaining steps. A short beep will be heard. 

The pump will run and empty the contents of the selected tank through the 8 ft black hose into the collection 
container. 

5.

 

Press the 

STOP

    button when fluid is no 

longer leaving the machine through the 
black hose and the selected tank is empty. 
The pump will stop running. The 

4 LITER

    

will be flashing. A short beep will be heard. 
Check that the tank is empty. 

6.

 

Press the 

STOP

    button again. The 

12 LITER 

will be flashing. A short beep will be heard. 
This programs the minimum weight. 

7.

 

Place two 5 kg or one 10 kg calibration 
weight on the top of the selected tank.  
(10 kg = 22 lbs) 

8.

 

Press the 

STOP

    button. The 

12 LITER

    will 

be illuminated. A short beep will be heard. 
This programs the maximum weight. 

9.

 

Remove calibration weight(s) and replace 
rear cover.  

10.

 

Press the 

STOP

    button again. A short beep 

will  be  heard.  The  machine  returns  to 
regular operating mode.

 

 
 
 

     

 

 

 

 

 

 

 

 

USED

FLUID

TANK

FLUID

TANK

NEW

CALIBRATION WEIGHT

COLLECTION

CONTAINER

LOAD CELLS

8 FT.

BLACK HOSE

COUPLER

10 kg

ADAPTER HOSE
WITH OPEN END

5

6

0

-8

0

4

1

4

-0

0

Summary of Contents for FluidPRO ATX-3 PLUS BOOST
























Reviews:

No comments