manualshive.com logo in svg

MAHLE FluidPRO ATX-3 PLUS BOOST, Operation Manual, Page: 12 / 23

Share
Download
MAHLE FluidPRO ATX-3 PLUS BOOST Operation Manual Download Page 12

Page 11 

DIPSTICK MODE: CONNECTING TO THE  

TRANSMISSION SYSTEM 

 
 
 
 
 

 

 

1.  Remove transmission dipstick. 
2.  Hold notched end of Dip Tube Hose even with the end of the dipstick as shown above. 
3.  Position Slide Indicator so that Dip Tube Hose will insert one inch deeper into the transmission. 

 

4.  Insert notched end of Dip Tube Hose into transmission so the Slide Indicator is even with the top of the 

dipstick port as shown above. 

5.  Attach Quick Coupler to other end of Dip Tube Hose. 
6.  Insert Quick Coupler into fitting on end of black hose on left side of ATX-3 PLUS BOOST. 

7.

  Connect red (positive) clamp on power cable to red (positive) terminal on vehicle battery. Connect the 

black (negative) clamp to a ground on vehicle frame. All lights on keypad should illuminate for one 
second and buzzer should pulse. If not, check connections and make sure REVERSE POLARITY light is 
not illuminated.

 

 

IMPORTANT 

 

Check transmission fluid level according to manufacturer’s instructions before 

connecting the ATX-3 PLUS BOOST. 

 

Transmission must be up to operating temperature 

 

Adjust fluid level if required 

Summary of Contents for FluidPRO ATX-3 PLUS BOOST
























Reviews:

No comments