background image

3

SAFETY

THIS      SAFETY      ALERT      SYMBOL      INDICATES      IMPORTANT 

SAFETY MESSAGES IN THIS MANUAL. WHEN YOU SEE THIS SYM-

BOL. CAREFULLY READ THE MESSAGE THAT FOLLOWS AND BE 

ALERT TO THE POSSIBILITY OF PERSONAL INJURY OR DEATH.

IMPORTANT:

 

To prevent personal injury, follow 

the safety messages in this manual. Follow the in-
structions carefully

The procedures recommended and shown in this 
manual are good, effective service methods.
However, all possible procedures and service haz-
ards may not be covered. Therefore, if you use 
a tool or procedure not recommended, you must 
make sure that the method you select is a safe 
method.

 

 WARNING:

 Read operators manual 

to familiarize yourself with control le-
ver functions.

 

 WARNING: 

Operate tractor and 

equipment controls from the seat po-
sition only.

 

 Any other method could result in seri-
ous injury

 

 WARNING: 

Unauthorized modifica-

tions to this machine can cause injury 
or death.

 

 Do not make unauthorized modifica-
tions to this machine.

 

 WARNING: 

Missing shields, guards 

or access panels can cause injury or 
death.

 

 Before you start the tractor engine 
and move this machine, always install 
all shields, guards or access panels 
correctly.

 

 

CAUTION: 

To prevent personal in-

juries when working with machinery, 
use safety shoes, a hard hat, safety 
glasses or goggles and tight fitting 
clothing. Use a brass or bronze ham-
mer or driver when positioning hard-
ened steel parts.

 

 CAUTION: 

Use a clip on air Chuck, 

extension hose with gauge and stand 
away from the tire while inflating to 
prevent the possibility of personal in-
jury due to a tire and rim separation, 
etc.

 

 WARNING: 

Hydraulic oil or diesel 

fuel leaking under pressure can pen-
etrate the skin and cause infection or 
other injury.

 

 To prevent personal injury:

 

 Relieve all pressure, before discon-
necting lines.

 

 Be for applying pressure, make sure 
all connections are tight and compo-
nents are in good condition.

 

 Never use your hand to tighten for 
suspected leaks under pressure.

 

 Use a piece of cardboard or wood for 
this purpose.

 

 If injured by leaking fluid, see your 
doctor immediately.

 

 WARNING: 

Never operate the engine 

in a closed building.

 

 Proper ventilation is required under 
all circumstances.

Summary of Contents for 3016























Reviews: