24
BA320101-en
Pos: 100 /Technis che Dok umentation/A lle G eräte/ Überschr iften/Üb erschriften 1.1/Ö/ Überschr ift 1.1: Öls tand prüfen @ 20\m od_1268827315211_ 75.d ocx @ 827233 @ 1 @ 1
6.4
Checking the Fluid Level
Pos: 101 /Technis che Dok umentation/Hebetechnik/ 00 H BZ A lle/Inhalte/Info!/Inhalt: I nfo - Tausch von Ö l und Drucks chläuchen_ 12p t @ 26\m od_1325753763930_ 75.docx @ 1147073 @ @ 1
•
Replace the hydraulic fluid periodically, depending on aging, soiling and water
absorption.
•
When topping up, use fluid with the same specification only.
•
If the lift is operated permanently at an ambient temperature of < 15 °C (59 °F),
use hydraulic fluid with a lower viscosity.
•
The pressure hoses should be replaced as required, but after six years at the
latest.
Pos: 102 /Technis che Dok umentation/Hebetechnik/ 32 Stemp el-Hebeb ühnen/ 0001 S tempel-Hebebühnen Alle/Inhalt/Inhalt: Hydrauliköl nachfüllen Stemp el_H BZ @ 26\mod_ 1326035058602_75.d ocx @ 1147815 @ @ 1
1 Fully lower the lift and any accessory equipment.
2 Remove the center cover.
3 Remove the filler screw at the hydraulic power unit.
4 When checking the fluid level using the dipstick, do not screw in the filler screw.
The fluid level should be between the top and bottom level marks.
5 Refill fluid with HLPD 22 / HLP 22 (biodegradable) specification. Capacity is
indicated on the reservoir.
6 Completely screw in the filler screw.
Pos: 103 /Technis che Dok umentation/A lle G eräte/ Überschr iften/Üb erschriften 1.1/SCH/ Überschrift 1.1: Schmierstellen @ 14\m od_1241506822762_ 75.docx @ 370057 @ 1 @ 1
6.5
Greasing Points
Pos: 104 /Technis che Dok umentation/Hebetechnik/ 32 Stemp el-Hebeb ühnen/ 0001 S tempel-Hebebühnen Alle/Inhalt/Inhalt: 3200 S chm ierstellen Stempel-H BZ @ 28\m od_1335184053867_75.d ocx @ 1588853 @ @ 1
•
Lightly oil the entire length of the ram and gear rack every six months or as
required (e.g. in the event of noise).
•
Inspect the support arm extensions every six months for smooth operation and
lubricate if necessary.
•
Inspect the support plate threads every six months for smooth operation and
lubricate if necessary.
•
Inspect the rubber pads every six months for wear and replace if necessary.
Pos: 105 /Technis che Dok umentation/Hebetechnik/ 32 Stemp el-Hebeb ühnen/ 2701 ES SQ UARE II 3.0/ BA/Inhalt: 3227 S chm ierstellen (Bild) @ 28\mod_ 1337674652817_ 0.d ocx @ 1598859 @ @ 1
Pos: 106 /-----Format- ----/MANUE LLE R UMBRUCH Seitenumbruch @ 0\mod_ 1134403577687_0.docx @ 1277 @ @ 1
