background image

1 - Table of Contents 

ExpressCard 2000| Instant Issuance Card Personalization System | XY Transport Module Replacement Procedure 

 
Page 4 

Table of Contents 

Table of Contents ............................................................................................................................... 4

 

1

 

Required Tools, Materials, and Documents ........................................................................... 5

 

1.1

 

Required Tools ..................................................................................................................... 5

 

1.2

 

Suggested Tools .................................................................................................................. 5

 

1.3

 

Required Materials ............................................................................................................. 5

 

1.4

 

Suggested Materials ........................................................................................................... 5

 

1.5

 

Required Software and Documents ................................................................................. 5

 

2

 

Introduction ................................................................................................................................. 6

 

3

 

XY Transport Module Replacement Procedure ...................................................................... 7

 

3.1

 

Prepare the Device ............................................................................................................. 7

 

3.2

 

Remove / Re-install the XY Transport Module ............................................................... 8

 

3.3

 

How to Calibrate the XY Transport Module ................................................................... 12

 

 

Summary of Contents for ExpressCard 2000















Reviews: