background image

ExpressCard 2000| Instant Issuance Card Personalization System | XY Transport Module Replacement Procedure 

 
Page 2 

Copyright © 2006 - 2014 MagTek, Inc. 
Printed in the United States of America 

 
Information in this publication is subject to change without notice and may contain technical inaccuracies 
or graphical discrepancies.  Changes or improvements made to this product will be updated in the next 
publication release.  No part of this document may be reproduced or transmitted in any form or by any 
means, electronic or mechanical, for any purpose, without the express written permission of MagTek, Inc. 
 
MagTek® is a registered trademark of MagTek, Inc. 
MagnePrint® is a registered trademark of MagTek, Inc. 
Magensa™ is a trademark of MagTek, Inc. 
MagneSafe™ is a trademark of MagTek, Inc. 
ExpressCard 2000

 is a trademark of MagTek, Inc. 

 
Microsoft® and Windows® are registered trademarks of Microsoft Corporation. 
All other system names and product names are the property of their respective owners. 

Table 0.1 - Revisions 

Rev Number 

Date 

Notes 

1.01 

09/22/2014 

Initial release derived from 99875607-5.01-DRAFT 

 
 

 

Summary of Contents for ExpressCard 2000















Reviews: