Part Number 110599
Revision Date, February 23, 2012
These Magswitch Multi Angle Tools Are Designed To Hold Small And Medium Sized Pieces Of Steel In
Place Until A Tack Weld Can Be Performed. Using Patented Technology, These Devices Have Tremendous
Holding Power On All Sides Of The Side Plates, As Well As A Great Amount Of Shear Force Holding
Strength To Reduce Sideways Movement. The unit can be positioned in order to use as an effective
Magnetic Vise (Magvise). On/Off Control And Easy Cleaning Of Debris Make These The Perfect Choice!
Read All Instructions! Failure To Follow All Instructions Listed Below May Result In An Unsafe Or Dangerous Condition.
General Information
o
All magnets need to be
kept at a safe distance
from all magnetic storage devices, electronics and credit cards etc…
o
Ensure that the Magswitch Multi Angle is
stored in the “off” position
when not in contact with Ferromagnetic metals. . The Multi Angle can be left
ON or OFF indefinitely without harm. When ON and near Ferromagnetic metals there will be a sudden and powerful attraction.
o
Never use a Magswitch Multi Angle to lift any materials overhead or where their release would cause injury or property damage.
o
DO NOT attempt to disassemble or alter
the Magswitch Multi Angle; there are no user serviceable parts inside the device.
o
All Magswitch products are
designed for normal work/jobsite conditions
, do not use underwater or in a hazardous environment
o
DO NOT use the Magswitch Multi Angle if it is damaged or is not working properly
. Severe injury can occur if this device is not used properly and
safely.
o
DO NOT expose the Magswitch magnets to temperatures above 176deg Fahrenheit (80 Celsius)
. High temperatures will permanently degrade the
magnet’s effectiveness and may result in an unsafe condition.
o
Never use a Magswitch Multi Angle for OVERHEAD LIFTING
or to transport material.
o
Not recommended for painted or finish coated surfaces
as these will reduce the magnetic bond and the finish may be damaged.
o
This product contains PTFE lubricant
. For MSDS information contact Magswitch.
o
Always keep the bottom of the magnet and side plates clean and free of debris and rust.
If needed wipe with WD40 or light oil
To use the Multi Angle (Mounts to flat or round Ferromagnetic steel)
o
Always
test the connection
before attempting to use the Magswitch Multi Angle to ensure that it is capable of holding the material securely.
o
Numerous factors can negatively affect the strength
of the magnetic bond. Dirt, debris, oils and grease, painted surfaces and any gap between the
magnet and the metal surface will decrease the bond.
Ensure that the connection point is clean
and free of these factors.
o
Thicker metals will be held more strongly than thinner metals.
.
E.g.: 1/4" (6mm) steel will be held more strongly than thin gauge metals.
o
Flat steel will be held more strongly than round bar stock or tube steel.
o
Avoid sudden jerking or Shock force
as this will cause the magnet to lose its hold.
o
Never use the Multi Angle as a welding ground or as part of an electric circuit.
o
For safe operation, the
bottom surface of the Pole Plates must always be Flat and Smooth
. If necessary, it is possible to sand the Magnet face smooth
using 400 grit sandpaper and a flat surface.
Always file any burrs
that would interfere with full contact.
Multi Angle Operation
o
The handle on this Magswitch Multi Angle must be turned clockwise 180 degrees until it stops
in order to be turned “ON”. It is not possible to hold
the Magnet in place unless fully turned “ON”. Turn ON only when in contact with ferromagnetic steel.
o
To release the magnetic hold, Press down on the handle and turn the handle in the counter clockwise direction until it stops. Remove all items
attached to or hanging from the Multi Angle before turning off!
The Magnet will
turn off and release immediately
upon turning the handle, Use
Caution to ensure that it is safe to release the magnet and that nothing will fall or become dangerous.
o
This Magswitch Multi Angle is capable of
exceptional Break-Away force
holding power; Magswitch Magnets are exceptionally strong in
Shear Force
as well
. Prying force is the least powerful
of the holding capabilities and great care must be used when attempting to use this device with Pry force.
See illustrations below.
Magswitch Limited Warranty
Magswitch products are covered by a One Year Limited Warranty on Material and Workmanship. Warranty is Non-Transferable.
Magswitch reserves the right to inspect all product claims under warranty. Any alteration of the device voids this warranty.
User assumes all risk for the proper use of this device and for ensuring product suitability for intended application.
This warranty shall not cover any incidental or consequential damages due to the improper use or failure of this device.
All Magswitch products are intended for the use identified on the package - not intended for resale or integration into products for resale. Contact Magswitch for inquires on integration of
technology. Australian Patent: 753496, Chinese Patent: 254155, New Zealand Patent: 518865, Singapore Patents: 88931; 103413, South Africa Patents: 2002/3752; 2004/1785, US
Patents: 6,707,360; 7,012,495. Additional Patents and Patent Applications Pending.
Multi Angle 400/1000 Magvise
Operation and
Instruction Manual
Magswitch Technology Inc.
8774 Yates Dr #140
Westminster, Co 80031
www.Magswitch.com.au
P
ull
for
ce
—
S
tronge
st
Hold
Pull Sideways
Shear force down or sideways-
Less Holding Capability
Pry Force—LEAST Holding Capability
Pry Force
Pull Force – MOST Holding Capacity
