MAGSTIM BiStim2 Operating Manual Download Page 7

 

Magstim BiStim² 

 

 

Operating Manual 

 

© The Magstim Company Limited 

MOP02-EN-02 

 

 

 

 

Explosive  and  Flammable  Atmospheres: 

The  Magstim  Bistim²  and  accessories  must  not  be 

used  in  an  explosive  atmosphere,  around  explosive  gases  or  in  the  presence  of  flammable 
anaesthetics. 

 

Protective Earth: 

To avoid the risk of electric shock, the Magstim Bistim² must only be connected 

to a supply mains with protective earth.

 

 

Modification: 

No modification of this equipment is allowed.

 

 

Discharge  noise:

  when  the  magnetic  pulse  is  delivered,  a  discharge  click  is  produced  that  may 

startle. The use of ear protection is recommended. 

 

Seizures:

  cortical  magnetic  stimulation  runs  the  risk  of  inducing  seizures.  Magstim  concurs  with 

the  advice  given  in  the  paper  titled  “Safety,  ethical  considerations  and  application  guidelines  for 
the  use  of  TMS  in  clinical  practice  and  research”  by  Rossi  et  al  (2009)  in  respect  to  screening 
candidates prior to administering TMS. 

 

Environmental  Conditions

*

The  system  must  not  be  used  or  stored  under  environmental 

conditions that fall outside those specified in section 6.3 of this operating manual. 

 

Stacking  Limit: 

Magstim  200²  units  may  be  stacked  on  top  of  each  other,  but  must  not  exceed 

the stacking limit specified in Section 6 of this operating manual. If this limit is exceeded, the stack 
may  become  unstable  and  overbalance  risking  injury  to patients  or  users  and  risking  damage  to 
the unit’s themselves. 

If  the  stacking  limit  is  reached  it  can  have  a  weight of  up  to  80kg. Ensure  that the  surface  upon 
which to system is to be placed is capable of supporting this weight. Failure to do so may result in  
injury or damage. The weight for each individual 200² unit is in excess of 20kg

 

 

Carrying

*

On  no  account  should  the  Bistim²  connecting  module  be  used  as  a  carrying/gripping 

point when transporting its host Magstim 200² unit. The Bistim² connecting module and its fixings 
are  not  designed  to  be  subjected  to  this  level  of  force  and  the  Bistim²  connecting  module  will 
become  detached  from  its  host  unit.  This  could  result  in  damage  to  Magstim  200²  unit,  Bistim² 
connecting module, or those transporting the equipment

 

 

Connecting Equipment: 

Only equipment listed in Section 1.3 may be connected to the Magstim 

BiStim².  Equipment that meets the relevant IEC standard may be connected to the rear  interface 
ports at the rear of the Magstim Bistim². See Appendix B for further details.

 

Summary of Contents for BiStim2
































Reviews: