background image

29

MDC CONTROLLER INFORMATION DISPLAYS, FUNCTIONS, AND RESET

The Magnum Digital Controller (MDC) constantly monitors vital generator and engine functions for a number of 
operation, alarm and fault conditions. When a fault condition occurs, the engine will shut down automatically and the 
Liquid Crystal Display (LCD) window will show the fault that has caused the shutdown. To resume operation, the 
fault condition must be resolved. To reset the controller and resume operation, press the “FAULT RESET” button. 

The operation of the Magnum Digital Controller (MDC) is divided into the following sections:

MAGNUM DIGITAL CONTROLLER (MDC) - GENERATOR OPERATIONAL STATUS

The Magnum Digital Controller (MDC) displays the operational status of the generator using the following codes:

MAGNUM DIGITAL CONTROLLER (MDC) - ALARM MANAGEMENT

The Magnum Digital Controller (MDC) is capable of displaying the following alarms:

No.

Engine State

Description

1

AfterCool

Engine aftercooling, Cooling Pump output is closed.

2

Cooling

The unit is cooling before stop.

3

Cranking

Engine is cranking.

4

EmergMan

Emergency Manual gen-set operation.

5

Init

Autotest during controller power on.

6

Not Ready

The unit is not ready to start.

7

Pause

Pause between start attempts.

8

Prestart

Prestart sequence in process, Prestart output is closed.

9

Ready

The unit is ready to run.

10

Running

The unit is running at nominal speed.

11

Shutdown

Shutdown alarm is activated.

12

Starting

Starting speed is reached and the 

idle timer

 is running.

13

Stop

Stop.

No.

Electrical State

Description

1

StabilTO

Stabilization Timeout

No.

Type

Description

1

Sensor fail (FLS)

Sensor fail is detected when measured value is 6% out of the 
selected characteristic. Sensor fail is indicated by ##### symbol 
instead of measured value. Note: Oil Temp for John Deere engines 
will always display #####.

2

Warning (WRN)

When warning comes up, see list of possible alarms.

3

Shutdown (SD)

When the shutdown alarm comes up the digital controller opens 
outputs GCB CLOSE/OPEN, FUEL, SOLENOID, STARTER and 
PRESTART to stop the engine immediately.

Summary of Contents for MMG75D

























































Reviews: