manualshive.com logo in svg

Magnum Dimensions ME-AGS-S, Owner'S Manual, Page: 33 / 38

Share
Download
Magnum Dimensions ME-AGS-S Owner'S Manual Download Page 33

27

 

© 2016 Sensata Technologies

Operation

4.3.1 Operational 

Notes

•  To manually stop the generator during the run time cycle, simply 

press the remote switch to the 

OFF

 position.

•  If a fault condition occurs, press the AGS remote switch to 

OFF

 

and then back to the 

ENABLE

 or 

TEST

 position. If the problem 

persists, refer to the Troubleshooting section in this manual.

•  When the AGS remote switch is placed in the 

OFF

 position, 

all AGS generator start functions are disabled. The 

STATUS

 

indicator is also off when the switch is in this position.

•  Once the generator has completed the 

RUN TIME HOURS

, the 

AGS immediately begins to monitor the 

START TEMP °F

 and 

START VOLTS DC

 settings for the next autostart cycle.

•  It is recommended that the AGS remote switch be set to the 

OFF 

position if the connected generator is placed into storage or left 

unattended for extended lengths of time.

•  If using the temperature start feature in an RV coach, set 

the air conditioner thermostat to match the 

START TEMP °F

 

setting. If using two air conditioners, it is suggested that the 

second air conditioner thermostat be set 2°-5° higher than the 

fi

 rst air conditioner. This staggered setting allows the 

fi

 rst  air 

conditioner to start and run in an effort to keep the coach cool. 

If the temperature continues to rise inside the coach, the second 

air conditioner turns on to further cool the coach.

•  When the generator starts successfully, the 

STATUS

 indicator 

turns solid green. The generator runs until the 

RUN TIME HOURS

 

setting is reached, at which time a stop signal is sent to the 

generator.

•  If the generator is running when either switch is placed in 

the 

TEST

 position, the generator stops and then starts again. 

The generator then runs for approximately 30 seconds before 

shutting off.

•  There is a two minute delay before the AGS attempts to start 

the generator if the voltage to the AGS controller falls to the 

START VOLTS DC 

setting. There is no delay if the AGS attempts 

to start the generator when the temperature around the remote 

switch rises to the 

START TEMP °F

 setting.

Summary of Contents for ME-AGS-S







































Reviews:

No comments