manualshive.com logo in svg

Magnetrol Pulsar R86, Operating Manual, Page: 30 / 52

Share
Download
Magnetrol Pulsar R86 Operating Manual Download Page 30

30

58-645 Pulsar® Model R86 Non-Contact Radar Transmitter – PROFIBUS PA Output

4.1.3 Diagnostic Indicator Table

Below is a listing of the Model R86 diagnostic indicators, showing their priority, explanations and
recommended remedies. (Priority 1 is highest priority.)

Priority

Indicator Name

Default

Category

Explanation

Remedy (Context Sensitive Help)

1

Software Error

Failure

Unrecoverable error occurred in stored
program.

Contact MAGNETROL Technical Support.

2

RAM Error

Failure

RAM (read/write) memory failing.

3

ADC Error

Failure

Analog-to-digital converter failure.

4

EEPROM Error

Failure

Non-volatile parameter storage failing.

5

Analog Board

Error

Failure

Unrecoverable hardware failure.

6

Spare Indicator 1

OK

Reserved for future use.

7

Default

Parameters

Saved parameters are set to default
values.

Perform complete Device Configuration.

8

Spare Indicator 2

OK

Reserved for future use.

9

Sweep Time Error

Failure

Analog board sweep time error

Contact MAGNETROL Technical Support.

10

Spare Indicator 3

OK

Reserved for future use.

11

Too Many Echoes

Failure

Excessive number of possible echoes
detected

Check Settings: Dielectric, Sensitivity.
Check Polarization.

12

Safety Zone Alarm

Failure

Risk of echo loss if liquid rises above
Blocking Distance.

Ensure that liquid cannot reach Blocking
Distance.

13

Echo Lost

Failure

No signal detected.

Check settings:

Dielectric Range

Increase Sensitivity.
View Echo Curve.

14

Spare Indicator 4

OK

Reserved for future use

15

Config Conflict

Failure

Measurement type and primary variable
selection parameters are inconsistent.

Confirm proper configuration. 
Check Measurement Type.

16

High Volume Alarm

Failure

Volume calculated from Level reading
exceeds capacity of vessel or custom
table.

Check settings:

Vessel Dimensions,
Custom Table entries

17

High Flow Alarm

Failure

Calculated flow exceeds maximum for
flume or custom table.

Check settings:

Vessel Dimensions,
Custom Table entries

18

Spare Indicator 5

OK

Reserved for future use.

19

Initializing

Function

Check

Distance measurement is inaccurate
while internal filters are settling.

Standard start-up message. Wait for up
to 10 seconds.

20

Config Changed

Function

Check

A parameter has been modified from
the User Interface.

If desired, reset Config Changed
indicator in ADVANCED CONFIG menu.

21

Spare Indicator 6

OK

Reserved for future use.

Summary of Contents for Pulsar R86





















































Reviews:

No comments