Magnavox 32ME306V, Owner'S Manual

Page: 15 / 39

These operations are accessible by remote control.
Some may also be accessible by the main unit's control
panel.
Initial setup
This section will guide you through the unit’s Initial setting which
includes selecting a language for your On-screen menu and
Autoprogram, which automatically scans and memorizes viewable
channels.
Before you begin:
Make sure the unit is connected to an antenna or cable.
1
After making all the necessary connections, press
B
to turn
on the unit.
●
It may take a few moments to turn on the unit for the first
time.
●
Initial setup
menu appears automatically after the unit is
turned on.
2
Use
H I
to select the On-screen language from the choices
(
English
/
Español
/
Français
) on the right side of the TV
screen, then press OK .
3
Use H I to select Voice guide to
Off
or
On
on the right side
of the TV screen, then press OK .
4
Use
H I
to select Antenna for TV channels or Cable for CATV
channels, then press OK .
Skip Back OK
Select
Skip
Cable
Antenna
ANTENNA IN
Or
Cable
Antenna
Select your signal source.
jack.
Make sure the antenna is connected to "ANTENNA IN"
Initial setup
–
When
Antenna
is selected, the TV detects antenna
signals. It searches for DTV and analog TV channels
available in your area.
–
When Cable is selected, the TV detects signals supplied
by cable. It searches for DTV, analog TV and cable
channels available in your area.
●
Autoprogram
will begin.
Skip
0 ch Analog channels
0 ch Digital channels
0%
complete.
Auto programming may take more than 20 minutes to
Please wait while the system is scanning for channels.
Initial setup
5
Use
H I
to select the desired location setting, then press
OK
.
Home is the ENERGY STAR
N
qualified setting.
OK
Select
Home
Retail
Initial setup
Demo with fixed settings.
“Retail” mode is optimized for Store
usage for home use.
and is optimized for efficient energy
“Home” mode is Energy Star qualified
Location:
●
Select Home , the unit is set to maximize the energy
efficiency for home setting and it can be adjusted through
a choice of picture and sound quality according to your
preference. Use this setting to remove the E-sticker, if
visible on the display.
L
p. 30
●
You must set
Home
in step
5
. Otherwise,
Picture
and
Sound
settings you adjusted will not be memorized after the unit
goes into standby mode.
●
When the Initial setup is completed, the lowest memorized
channel with the confirmation message of the location
setting will be displayed on the TV screen.
●
Select Retail , the unit will be set up with predefined settings
for retail displays. In this setting, the power consumption
may possibly exceed the limited requirement limit of the
ENERGY STAR
N
qualification.
Note(s)
●
If you are not receiving a signal from your cable service, contact the cable
provider.
●
If you press B or MENU during Autoprogram, this setup of TV channels will be
cancelled.
●
The initial Autoprogram function can be executed for either Antenna or Cable only
once. When you change the connection (Antenna / Cable), select Autoprogram
again.
L
p. 23
●
If there is no signal input from the antenna terminal and no operation for several
seconds after you turn on the unit, helpful hints appears. Follow the instructions
listed on the TV screen.
Skip OK
Select
Later
Retry
Initial setup
####
####
the appropriate source input.
press "SOURCE" key on the remote control to select
the input which you have connected to the box and
If you are using a cable or satellite box, please confirm
installation process searches this connection.
ANTENNA IN jack on the back of the TV, the channel
Verify that you have a cable connected to the
Try Autoprogram again?
No channel is registered.
After an initial setup is completed...
●
If you want to scan the channels automatically again.
Autoprogram L p. 23
●
You can add the desired cable and analog channels not
memorized by Autoprogram.
Add channels
L
p. 24
●
If you want to change to another language.
Language
L
p. 31
●
If you want to change the location setting.
Location
L
p. 30
15 .
English