background image

Step 3:  5-Pin Power Harness Installation

The power harness contains 3 wires and two vacant sockets. Follow the wiring recommendations enclosed

for each wire.

4

Step 2:  10-Pin Main Harness Installation 

(Continued)

Brown Wire: 

(Siren + Output)

Connect the brown wire to the positive wire from the siren. Ground the remaining wire from the siren for

proper operation.

Blue Wire:

(Optional Grounding Sensor Input) 

The blue wire is an instant grounding trigger input for optional hood/trunk grounded pin switches or any

electronic sensor.

Green Wire:

(Grounded Door Pin Switch Input) 

The green wire connects to the common wire of the vehicle that switches on the dome light. Normally

this wire is located at one of the door jamb switches. For some vehicles it may be necessary to connect

the green wire directly to the switched turn on wire at the dome light. The green wire connects to

negative switched circuits only.

Violet Wire:

(Positive Door Pin Switch Input) 

The violet wire connects to the common wire of the vehicle that switches on the dome light. Normally

this wire is located at one of the door jamb switches. For some vehicles it may be necessary to connect

the violet wire directly to the switched turn on wire at the dome light. The violet wire connects to positive

switched circuits only.

Second Vacant Socket:

The second vacant wire socket provides a 1 second pulsed ground (300mA) output when channel #2 is

activated. (See Optional Accessory Connections) (Page 10-11)

Red / White: 

(Pulsed Parking Light Relay Output)

Connect the red/white wire to the parking light wire coming from the headlight switch. (Do not connect

the red/white wire to the dashboard lighting dimmer switch. Damage to the dimmer will result) use a volt

meter to test the connection point before connecting the red/white wire. While checking, rotate the

dimmer switch to make sure you do not have the dimmer lead. The limitation of the red/white wire is 10

Amp max. Do not exceed this limit or damage to the alarm and parking light relay will result.

Pink:

(Parking Light Relay Input)

The pink wire is the input to the flashing parking light relay. The connection of the pink wire will determine

the output polarity of the flashing parking light relay. Connect the pink wire to (+) battery to have (+)

output from the relay or connect the pink wire to frame ground to have ground output from the relay. 

Power Harness

First Socket

Second Socket

Summary of Contents for CARBINE PLUS-5000





















Reviews: