background image

       1-800-MAGLINE (624-5463) 

 

 

 Page 13                                               www.magliner.com

CooLift

®

Battery Charging Warnings:

 

Use only Magliner chargers designated for use with CooLift.

 

Do not expose charger to rain or snow.

 

To prevent risk of fire, use the charger only in a dry, well    

 

  ventilated room without flammable fluids or explosive gases.

 

Do not allow clothing, blankets or other material to cover   

 

 

battery charger during charging process.  Ensure there is proper  

 

ventilation in area used for battery charger and batteries.  

 

Use of an attachment not recommended or delivered by the  

  battery charger manufacturer may result in a risk of fire,    

 

  

 

electric shock or injury to persons.

 

Avoid using an extension cord as it can present risk of fire and electrical shock.  Never use a  

 

 

household extension cord if the charger plug does not reach outlet. If an  

 

 

 

 

 

extension cord must be used, use a three conductor No. 14 AWG (or heavier) cord with  

 

 

 

proper ground, in good electrical condition and kept as short as possible.

 

Make sure the cord is located such that it will not be a trip hazard or otherwise subject to    

 

 

damage or stress.

 

Do not operate a charger with a damaged cord or plug – replace immediately.

 

Do not operate a charger if it has received a sharp blow, been dropped, or otherwise  

 

 

 

subjected to damage or stress.

 

Do not disassemble the charging unit.

 

To reduce risk of electrical shock, unplug the charging unit from the AC power  

 

 

 

 

supply source before attempting any maintenance or cleaning.

 

Always unplug the charging unit before operating the Magliner CooLift.

 

Always use battery chargers supplied by Magline, Inc. Other battery charging units could    

 

 

cause damage to your batteries or personal injury.

 

Batteries generate gases that can be explosive. To prevent arcing or burning near batteries,  

 

 

do not disconnect the charger output connector from the charging port when the battery  

 

 

 

charger is in operation.  If an interruption of the charging cycle is desired, move the battery   

 

 

charger switch to OFF, disconnect it from the power supply source and then disconnect the  

 

 

charging connector from the charging port.

 

To avoid damage to battery charger connectors and cords, disconnect by grasping the plug  

 

 

body and pulling it straight out of the outlet or receptacle. DO NOT pull on the cord. DO NOT  

 

 

twist, rock, or pull the connector sideways.

 

The metal tip on the end of the plug may be hot when it is first unplugged.

*Battery has a warranty of six (6) months

Summary of Contents for CooLift CTA Series





























Reviews: