background image

22

3. The lower blade should project forward, with respect to the upper 

one by 1.2 mm.

4. If you could not level the blades, drip a few drops of oil on the 

blades, turn on the machine for a while (30-40 seconds). After that, 

turn off the machine.

5. Slightly loosen the screws of the lower blade and align the blades.

6. After aligning the blades, be sure to tighten the mounting screws 

of the lower blade.

Oiling instructions

Comb guides

Length adjustment lever

1.  For optimum cutting performance, it is highly recommended to 

oil the blades after every use.

2. When using the oil for the first time, unscrew the cap and cut off 

the very end of the plastic tube with a pair of scissors.

3. Remove the blade guard and switch the appliance on.

4. Holding the clipper at a 45 degree angle, gently squeeze the oil 

tube and apply 2 drops directly onto the blades.

5. Leave the unit on for a further few seconds to allow the oil to 

thoroughly spread along the length of the blades.

6. Switch off the unit and remove any excess oil by gently dabbing 

with a cloth before using on hair.

This appliance is supplied with 4 comb guides: 3mm / 6mm / 10mm 

/ 13mm 

1.  To attach a comb guide, ensure the appliance is switched off. 

Position the comb guide over the front of the clipper blade and 

slide over the head. Push and click the rear of the comb guide into 

position.

2. To remove the comb guide, ensure the appliance is switched 

off. Push the tab on the rear of the comb guide away from the head 

and lift off.

The taper control lever enables fine cut adjustment for precision 

clipping.

 

-

To increase the cutting length, push the lever down.

 

-

To reduce the cutting length, push the lever up.

EN

Summary of Contents for MG-585





























Reviews: