background image

26

Making Power Supply

Connections

After making all signal connections, connect the left channel’s 

analog dc in

 on

the rear panel of the Nº30.5 to the 

left audio dc out

 on the rear panel of the PLS-

330; likewise, connect the right channel’s 

analog dc in

 on the rear panel of the

Nº30.5 to the 

right audio dc out

 on the rear panel of the PLS-330.

Connect 

digital dc in

 on the rear panel of the Nº30.5 to the 

digital dc out

 

on the

rear panel of the PLS-330.

Connect the AC cord to the AC power connector on the bottom panel of the PLS-
330, then connect the AC cord to the AC mains; the LED on the PLS-330 and the

standby

 LED on the Nº30.5 will light. After a few seconds, the Nº30.5 will begin

its self-test (the Display first shows 

INITIALIZING

, then each of the eight input

aliases, and finally 

LOCKING

 as it attempts to lock onto input 1).

The Nº30.5 is now ready to operate.

For optimal sonic performance and longevity, the Nº30.5/PLS-330 is designed to
remain powered at all times. The 

standby

 button is provided so that you may

turn off the display and disable the front-panel controls when the Nº30.5 isn’t in
use (see “Front panel, Nº30.5”).

Naming Your Inputs

All inputs other than 1 and 4 are labelled 

NOT USED 

as delivered from the factory,

and will need to be given appropriate names before they are used. Giving inputs
appropriate names is simple and greatly enhances the ease of use of your new
Nº30.5, especially for occasional users of the system. The available names are
shown on page 24. To give an input a new name:

1

SELECT THE INPUT YOU WISH TO RENAME

Note that the input to be renamed needs to be the selected monitored in-
put. The input which is currently selected to be sent out the digital record
path is irrelevant to the renaming process.

2

PRESS AND HOLD THE DIGITAL RECORD SELECT BUTTON

After a delay of approximately five seconds, the display will change to

NAME = 

(

the current name

), as shown below. If the current name for the

input is 

NOT USED

, it will be abbreviated to 

N.U.

This message informs you that the Nº30.5 is ready for you to change the
input’s name. (

Note that pressing and holding the 

digital record select 

but-

ton performs a different function than simply pressing it momentarily, which
would allow you to select a source for the digital record path.

)

Summary of Contents for mark levinson 30.5







































Reviews: