MACKISSIC MIGHTY MAG VMS25 Safety & Operating Instructions Manual Download Page 6

 

General Safety 

Operating this vacuum safely is necessary to prevent or minimize the risk of 

death or serious injury

. Unsafe operation can create a 

number of hazards for you.  Always take the following precautions when operating this vacuum: 

 

Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and 
themselves. 

 

Your Multi-Surface Vacuum is a powerful tool, not a plaything. Exercise extreme caution at all times. The design of 
this machine is to vacuum debris on turf or hard surfaces.  Do not use it for any other purpose. 

 

Know how to stop the vacuum quickly. 

 

Never allow people or pets to ride on the Multi-Surface Vacuum. 

 

Never start the engine without the debris bag attached firmly to the discharge tube. 

 

Never attempt to remove the debris bag while the Multi-Surface Vacuum engine is running. Debris may exit at high 
velocity out of the openings created in the seams as you unlatch the debris bag. 

 

Empty the debris bag after each use to prevent spontaneous combustion due to decaying material. 

 

Do not vacuum in sandy areas where you will vacuum large quantities of sand. 

 

Never operate the vacuum near hot or burning debris or any toxic or explosive materials. 

 

If the machine should start making an unusual noise or vibration, stop the engine and wait five (5) minutes to cool. Vibration 
is generally a warning of trouble. Disconnect the spark plug wire and inspect for clogging, damaged, or worn impeller, loose 
impeller bolt, loose impeller key, or loose engine mounting bolts. Clean and repair and/or replace damaged parts. 

 

Always shut off the Multi-Surface Vacuum engine, wait five (5) minutes to cool, and disconnect the spark plug 
wire before attempting to clear any obstructions. 

 

Always keep the equipment in a good safe operating condition. Always make certain nuts and bolts are tight and always use 
the supplied self-locking hardware; do not substitute. 

 

Use the Multi-Surface Vacuum only in daylight. 

 

While using the vacuum, do not hurry or take things for granted. When in doubt about the equipment or your surroundings, 
stop the machine and take the time to look things over. 

 

Never leave the machine unattended with the engine running. 

 

Do not operate the machine when under the influence of alcohol, drugs, or medication. 

 

See 

manufacturer’s instructions for proper operation and installation of accessories. Only use accessories approved by 

MacKissic Inc. 

 

A Note to All Users 

Under California law, and the laws of some other states, you are not permitted to operate an internal combustion engine using 
hydrocarbon fuels without an engine spark arrester.  This also applies to operation on US Forest Lands. All Multi-Surface Vacuum

’s 

shipped to California, New Mexico and Washington State are provided with spark arresters. Failure of the owner or operator to 
maintain this equipment in compliance with state regulations is a misdemeanor under California law and may be in violation of 
other state and/or federal regulations. Contact your State Park Association or the appropriate state organization for specific 
information in your area. 

 

Additional Information and Potential Changes 

MacKissic Inc. reserves the right to discontinue, change, and improve its products at any time without notice or obligation to the 
purchaser. The descriptions and specifications contained in this manual were in effect at printing. Equipment described within 
this manual may be optional.  Some illustrations may not be applicable to your machine. 

No list of warnings and cautions can be all-inclusive. If situations occur that are not covered by this manual, the operator must 
apply common sense and operate this Multi-Surface Vacuum in a safe manner. Contact us at www.MacKissic.com or call 1-
800-348-1117 for assistance. 

 

 

 

MULTI-SURFACE VACUUM 

Summary of Contents for MIGHTY MAG VMS25






























Reviews: