background image

16

Specifications

Enclosure

Materials:

 

MDF construction with black oak veneer. 
Sides:    0.75 in/19 mm thick 
Top:       1.5 in/ mm thick 
Bottom: 1.00 in/5 mm thick

Internal Volume:

 

.15 cubic feet/60.88 liters

Transducers

Low-frequency driver:

 

 

1-inch/05 mm die-cast frame, oversized ferrite magnet 
structure, 4-inch/100 mm voice coil, and over 45 mm cone 
excursion

Passive Radiator:

 

1-inch/05 mm mass-loaded 

System Specifications

Crossover Type:

 

Linkwitz-Riley, 4 dB/octave, variable 55 Hz to 110 Hz

Input Type:

 

Balanced differential XLR; Unbalanced RCA

Input Impedance:

 

0k

Ω

, balanced bridging 

10k

Ω

, unbalanced

Input Sensitivity:

 

89 dB SPL with a 100 mV (–17.8 dBu) input signal

Maximum Input Level:

 

+0 dBu

Signal Sense Threshold:

 

–74 dBu (0.155 mV)

High-Cut Filter (LFE):

 

7th order elliptical filter @ 110 Hz

Subsonic Filter:

 

– dB @ 15 Hz, rd-order Butterworth High-Pass filter

Input Protection:

 

RFI and level protected

Driver Protection:

 

Power supply tracking peak limiter

Thermal Protection:

 

Heatsink and Power Transformer temperature, auto reset

Amplifier Section

Rated power output (1% THD @ 100 Hz):  

400 watts rms into rated 8

Ω

 load

Burst power output (100 Hz sine with 10% duty cycle):  

500 watts

Distortion:

 

THD (0 Hz-00 Hz, from 1W to –1 dBr=5 W): 

 

< 0.0% (typically 0.005%)

Signal-to-Noise Ratio:

 

> 107 dB, referenced to 5 watts into 8 ohms

Acoustic Section:

Free-Field Frequency Response:

 

±1.5 dB, 0 Hz to 150 Hz

Lower cutoff frequency:

 

– dB @ 19 Hz

Maximum SPL:

 

 

117 dB SPL @ 1m

Residual noise:

 

 

< 8 dBA SPL @ 1m

General:

Power Consumption:

 

80 watts with musical program, loud mix 
  0 watts quiescent (idle)

Dimensions:

 

Height (including feet):   

1.0 in/5 mm 

Width: 

 

18.0 in/457 mm 

Depth (including grille): 

18.8 in/478 mm 

Overall Depth: 

 

1. in/541 mm

Weight:

 

 

94 lb/4.6 kg

LOUD Technologies Inc. is always striving to improve our 
products by incorporating new and improved materials, com-
ponents and manufacturing methods. Therefore, we reserve 
the right to change these specifications at any time without 
notice.

21.0 in/

533 mm

19.0 in/

483 mm

HRS120

WEIGHT

 94 lb/

42.6 kg

18.0 in/457 mm

18.0 in/457 mm

18.8 in/478 mm

21.3 in/541 mm

HIGH RESOLUTION

HIGH RESOLUTION

Summary of Contents for HRS120





















Reviews: