Operation
SCR system
cleaning
INHIBIT
Should only be activated when the environment
is unsafe to allow high exhaust temperatures
(e.g., in a building).
To activate function, press and hold the icon for
three seconds. The fuel gauge display is replaced with red
text HOLD 3 SECONDS.
SCR system
cleaning
FORCED
Allows a manual (parked) exhaust system
cleaning. It is used infrequently for unusual duty
cycles. If required, it will illuminate amber.
Should
NOT
be performed indoors.
HEST lamp
Do
NOT
park vehicle indoors when lamp is on.
Appears when the engine enters a SCR system cleaning.
This will not hinder normal vehicle operation.
Overriding
engine
shutdown
This should only be done in an emergency
situation (e.g., clearing a railroad) as engine
damage may occur.
Press the
PRESS HERE TO OVERRIDE
message that al-
ternate with
SHUTDOWN IN
message. The countdown
timer for shutdown will reset to 30 seconds.
Tools menu
Accessible through the fuel icon and gauge. Press and hold the fuel icon and gauge display for two seconds.
Tools and brightness symbols come up.
Pressing the brightness symbol will display the backlighting control function. Adjust if necessary.
NOTE:
Display will revert back to fuel icon and gauge if backlighting control function is not pressed for five
seconds or if the DEF icon and gauge are pressed.
Pressing the tools symbol brings up the languages menu and software version.
Tips and Shortcuts
Entering
Programming Mode
Ignition ON. Press and hold
PROGRAM
and
SELECT
at the same time, until the CDM display enters
programming mode.
Exiting
Programming Mode
Press
PROGRAM.
Changing Language
to English
Ignition OFF. Press and hold
HEADER INDEX
and
PROGRAM
and
SELECT.
Clearing Sub-Acres
Cab-Forward position. Ignition ON. Press
SELECT
until SUB-ACRES is viewed on the bottom line of
the display. Press and hold
PROGRAM
until SUB-ACRES changes to 0.0.
Disconnecting
Batteries
The battery disconnect switch is located just behind the batteries and can be accessed by opening the
maintenance platform. Ensure the switch is in the OFF position when servicing electrical components,
or when the windrower will not be used for periods longer than one week.
NOTE:
See M155
E4
Operator’s manual for complete instructions and detailed information
Header
Model
Application / System
Suggested Overload
Warning Setting kPa (psi)
Windrower Pressure
Relief Setting psi (kPa)
R-Series
Disc pressure
27,579 (4000)
28,958 (4200)
Reel / draper pressure
20,684 (3000)
22,063 (3200)
A-Series
D-Series
Knife / conditioner pressure
27,579 (4000)
28,958 (4200)
Header index mode is desirable in some crop and terrain
conditions because it allows the reel and conveyor to be
driven by reference to ground speed, so that header
systems speed up and slow down as ground speed
changes.
Operation of Header Index for REEL SPEED:
(A-Series and D-Series)
1. Clear all bystanders, start the windrower, and engage
the header.
2. While stationary with the GSL in PARK, use the REEL
SPEED control switch to set a minimum reel speed.
When operating at a ground speeds faster than the
minimum reel speed + header index value, REEL SPEED
display will change to REEL INDEX.
3. Adjust the header index value using the GSL REEL
SPEED switch.
Reel speed will be equal to Ground Speed + Index Value
or Minimum Reel Speed
(whichever is greater).
Operation of Header Index for DRAPER SPEED:
(D-Series Only)
Follow instructions above, using the CDM AUGER/DRAPER
speed control, rather than the GSL REEL SPEED switch.
Header Index Mode
M155
E4
Windrower Quick Card - Form 214813 Rev. A
Supplement to M155
E4
Windrower Operator’s Manual
Programming the CDM
Fuel and Diesel Exhaust Fluid (DEF) Display Module
Alarm Tone
Reason
Duration
When DEF or fuel level amber light first starts to blink (1/16th tank)
5 seconds
Ongoing intermittent
moderate tone until the
condition is corrected
When the SCR system cleaning INHIBIT
is active and system calls for a
passive SCR system cleaning
5 seconds, repeat
every 30 minutes
Single moderate tone
At the end of the delay for entering the brightness/tools menu
At the end of the delay when switch (icon) is activated
1
FUEL
and
DEF LEVEL
-
Amber light blinks when tank level reaches 1/16.
2
HIGH EXHAUST SYSTEM TEMPERATURE (HEST)
-
When active, icon is black with amber background.
When inactive, icon not visible.
3 SCR SYSTEM CLEANING INHIBIT
and
FORCED -
When active, icons are black with amber background.
When inactive, icons are gray.
Subject to change without notice
1
PROGRAM
- Press to enter/exit set-up modes
and for key shortcuts.
2
ENGINE WARNING
- Engine preheat, water
in fuel, engine malfunction, and stop engine.
3
RETURN TO CUT
- When green light is ON,
RETURN TO CUT function is active.
4
IGNITION
- Accessory, Stop, Run, Start.
5
HEADER INDEX
- When green light is ON,
reel/conveyor speed features are active.
6
AUGER / DRAPER SPEED
- Adjusts draper or
auger speed depending on header.
7
FLOAT
- Provides in-cab adjustments for
independent left/right header flotation.
8
HAZARD WARNING LIGHT
- Flashing amber
lights operate in both cab-forward and engine-
forward positions.
9
TURN SIGNAL
- Activates turn indicators and
scrolls through CDM set-up screens.
10
SELECT
- Changes bottom line of display and
works as the ENTER button in program mode.
