background image

 

11

 

FLYING THE MUSE 4  

 

The following information must not under any circumstances be taken as a 
manual for practicing paragliding. We would like to advise you of the Muse 4 ‘s 
features and important information for your flying and security.  

Preparing for take off: 

As for any aircraft a thorough pre-flight check must be made prior to each flight on the 
Muse 4! Before every launch check lines, risers and canopy for damage! Do not launch 
with even the slightest damage! 

Also check the maillons connecting the lines and the risers. They have to be closed 
tight. Put on the harness with maximum care and check the handle of the safety system 
and that all the flaps of the outer container are fastened securely and correctly. The 
main karabiner must also be checked carefully. Replace it if any damage is visible, or 
generally after 300 flying hours. Finally connect the risers to your harness with the main 
karabiners. 
Check carefully that they are properly closed. 

Attention! Never fly with an open main 

karabiner!  Do not take off if you find any damage on your equipment! 

Having unpacked and laid out the paraglider in a slight horseshoe pattern the following 
checks must be made:  

 

Checklist:       

Preparing the wing:

 

 canopy without any damage 

 risers without damage 

  maillons (quick links) closed tight 

  stitching of the main lines near the risers is o.k. 

  all main lines run free from the riser to the canopy, brake lines are free 

Putting on the harness: 

  rescue handle and deployment pins secure  

  buckles (leg- ,front riser) closed 

 main karabiners 

Before take off: 

 speed-system mounted and connected properly 

  risers not twisted 

  brake handle in hands, brake lines free 

  pilot‘s position relative to the wing (centred: all lines same tension) 

 wind direction 

  obstacles on the ground 

 free airspace 

 

 

Summary of Contents for Muse 4

































Reviews: