MAAX SPL 3838, Installation Manual, Page: 4 / 16

CAUTION: It is advisable to protect
the unit surface with a thin plywood or
cardboard shield while fastening the
flange to the framing.
Water Supply and Drain Connections
Refer to, and follow, the assembly and
installation instructions provided with the supply
valves and drain system. Carefully check all
fittings and connections for leaks .
Unit Surface Care
WARNING!
NEVER USE ABRASIVE MATERIALS
NOR ABRASIVE CLEANERS ON THE
UNIT SURFACE!
EXTREME CAUTION is urged regarding
the use of any cleaner, acid or solvent
on the unit surface.
READ, AND FOLLOW ALL PACKAGE
LABELS AND INSTRUCTIONS!
Through routine use, the unit surface can
collect residues from soap, bath additives
and natural body oils. Additional deposits
can also collect from minerals or particles
found in the water.
After each use, wipe the excess water
from the unit. This practice will reduce the
build-up of deposits and help maintain the
natural unit lustre.
Following a thorough surface cleaning,
an application of quality automotive wax
will help reduce major accumulations. The
actual schedule for cleaning, and waxing, will
depend on unit usage and water quality.
WARNING!
AVOID APPLYING WAX TO THE UNIT
BOTTOM!
• Routine Cleaning: Mild, non-abrasive
cleaner specifically formulated for gelcoat
and acrylic surfaces recommended.
(Rinse surface thoroughly.)
• Heavy Soap Deposits: Liquid ammonia
household cleaner, applied full strength.
(Rinse surface thoroughly.)
• Stubborn Stains: Liquid household
cleaner or hydrogen peroxide, applied
full strength. Place a saturated clean rag
directly on stain and let stand several
hours. (Rinse surface thoroughly.)
For extreme cases, buff area with white
automotive polishing compound until stain
disappears, and apply a quality automotive
wax to surface.
Wall
Framing
Fastening
Flange
Figure 3a - Securing Unit
Drill 1/8 inch hole
through flange at each
framing member
0.3" (8 mm)
Fill all holes with
silicone
Remplir les trous
avec du silicone
Llenar los agujeros
con silicona
Note: the bottom of all holes in the flange have
to be at least mm or 0.3” above the base threshold.
Note : Chaque trou dans la bride doit être à une distance
minimale de 8mm(0.3po.) de la surface de la base.
Nota : la parte inferior de todos los agujeros de la brida tiene
que ser al menos de 8 mm o 0,3” sobre el umbral de base.
Wall
Framing
Fastening
Flange
Figure 3b - Securing Unit
Secure unit
to framing with
1-1/4" screws
CAUTION: Protect unit surface
with a shield when fastening
• Hard Water Scales: Liquid scale
remover or white vinegar, applied full
strength. (Rinse surface thoroughly.)
• Mold/Mildew: Liquid mildew remover
or baking soda and water paste. Apply
paste and allow to fizz several minutes.
(Rinse surface thoroughly.)
• Construction Adhesive: Soften adhesive
with hand held dryer and peel off
adhesive. (Caution is advised when
using any electrical device near water.)
For stubborn cases, apply rubbing alcohol
or nail polish remover, full strength, to
adhesive. (Rinse surface thoroughly.)
WARNING!
BATH MATS OR OTHER ITEMS WHICH
ARE HELD IN PLACE USING SUCTION
AGAINST THE UNIT SURFACE MUST
BE REMOVED FROM THE FLOOR OF
THE UNIT AFTER EACH USE.
OVER A PROLONGED PERIOD, FAILURE
TO REMOVE THESE TYPES OF ITEMS
FROM THE BOTTOM OF THE UNIT CAN
RESULT IN SURFACE DAMAGE.
WARNING! THE UNIT BOTTOM
SHOULD BE CLEAR OF ALL
POTENTIALLY DAMAGING DEBRIS
AND THE SURFACE PROTECTED
BEFORE STEPPING INSIDE.
4