background image

17

17

PowerPool

Temperature

The maximum set temperature is 104°F (40°C) 
and the minimum set temperature is 80°F 
(26°C). The current water temperature will show 
on the display unless the primary pump has 
not been running, in which case two dashes 
(--) will show on the display. If two dashes are 
displayed, you must first start the pump by 
pressing the 

JETS 1

 pad. Wait until the water 

temperature is displayed (approximately 2 
minutes).

The set temperature of your PowerPool™ may 
easily be increased or decreased at any time 
using the 

WARM

 or 

COOL

 pads. When either 

of these pads is touched, the set temperature 
will be displayed in the LCD display window. 
Each successive touch will change the set 
temperature 1°F (0.5°C) in the chosen direction. 
After 3 seconds the LCD will automatically 
display the water temperature or dash lines.
If the PowerPool™ is set in Standard mode or in 
a filtration cycle, adjusting the set temperature 
may result in activating the heater. When 
the heater is operating, the heat icon will be 
displayed in the LCD.

JETS 1

Touch the 

JETS 

1 pad to activate the primary 

filtration and jet pump. The sequence of the 
jet action is: 

1 touch   = Low jets

 

 

2 touches  = High jets

 

 

3 touches  = Off

JETS 2 & JETS 3

Touch the 

JETS 2

 pad to activate the number 2 

Jet pump and Touch the 

JETS 3

 pad to activate 

the number 3 Jet pump. The sequence of jet 
action is: 

1 touch   = Low jets

 

 

2 touches  = High jets

 

 

3 touches  = Off

User’s Pads

User’s Pads are the buttons located on the 
topside control panel and are used to program 
various PowerPool™ functions (i.e., turn on 
PowerPool™ light, set temperature, etc.). The 
following table defines the pads:

Pad

Use

• Increase temperature
• Change time settings

• Decrease temperature
• Change time settings

• Turn internal PowerPool™ light 
  on or off

• Set or lock/unlock temperatures
• Set or lock/unlock panel settings
• Switch modes
• Set time and filtration cycles

• Activate primary filtration pump

• Activate therapy pump

• Change time of day setting, or
• Change set times of 
   PowerPool™ cycles
• Exit programming

• Activate therapy pump

Summary of Contents for Powerpool









































Reviews: