background image

13

13

PowerPool

ELECTRICAL INFORMATION

Important Safety Instructions

All electrical connections to this spa package
MUST be accomplished by a qualified  
licensed electrician in accordance with the 
National Electrical Code (NEC) and with state/
local electrical codes in effect at the time  
of installation.

NOTE: Prior to performing any service to 
the spa equipment, turn OFF all primary 
electrical power at the main circuit breaker 
or disconnect panel.

To make spa electrical connections, remove 
the exterior equipment access panel, locate 
the electrical control box, remove the control 
box cover and follow the wiring diagram on 
the inside of the control box cover.
Connections should be made using copper 
conductors 

only

. Connecting wires, circuit 

breakers, or fuses must all be sized to accom-
modate the Total Ampere load as specified 
on the equipment label.
This equipment is designed to operate on 
60Hz alternating current only, at 240 volts.

NOTE: All unions must be hand-tight and  
all slice valves must be locked in the OPEN 

position before filling or refilling spa! 

 

A clip is provided to help keep the slice 
valve open. Run spa and check for union 
leaks before reinstalling front panel.

Ground-Fault Circuit Interrupter

A qualified licensed electrician shall connect 
the spa to a circuit protected by a GFCI.  This 
is a requirement by the National Electric 
Code, article 680-42, and is also in compli-
ance with Underwriter’s Laboratories, Inc.

Installation Options

While knockouts are provided in the cabinet 
base to bring the conduit to the equipment 
compartment, a hole may need to be drilled 
in the pedestal or base if an alternate electri-
cal service entrance is desired.

Refer to the manufactures’s nameplate 
located on the kick plate to determine your 
spa’s ampere requirements. 

240 Volt Installation

Permanently Connected:
The Super Sport spa side must be connected 
to a 240 volt electric service.

Electrical Requirements:

240 volt, 60 Hz, single phase, 40 amp., 

• 

4-wire service (line 1, line 2, neutral, 
and ground or,

         *30 Amp Option
Note:  The heater can be activated only with 
the pump on low speed.  Only the spa light 
can be operating at the same time without 
disabling the heater.  See your authorized 
MAAX Spas dealer to select this option.

240 Volt Installation

Permanently Connected:
The Sport, Pro and Super Sport swim side 
must be connected to a 240 volt electric 
service.

Caution: Risk of electrical shock.
Read and follow all instructions.

Summary of Contents for Powerpool









































Reviews: