background image

 

8

1

0

2

 

s

e

c

i

v

r

e

S

M

2

M

 

©

  

0

1

Wireless keyfobs 

 

Supported functions  

The wireless keyfob has 4 buttons - Full Arm, Home Arm, Disarm and Panic. By default, only the Full Arm 
and Disarm buttons are active.  

To enable the STAY Arm button, you need to have at least one STAY zone. Please refer to the 
“Con guring the zones” section.  

To enable the Panic button of the keyfob, please refer to the “Con

ring the panic button” section.   

Pairing a wireless keyfob  

The RControl Alarm panel supports up to 16 wireless keyfobs. Two keyfobs are included in the standard 
kit and they are already paired.  

To use additional keyfobs you should  rst pair them with the alarm panel.  

NOTE: 

To be able to enter learning mode, make sure that the panel is

 DISARMED! 

To enter learning mode, press the “PAIR” button of the RF receiver of the panel. The red LED indicator of 
the RF receiver will turn ON. Press any button of the wireless keyfob 

(hold the button at least 1 sec)

The siren will beep once, which indicates that the keyfob was paired and the procedure was successfully 
completed.  

NOTE: 

It’s recommended to pair the keyfob with Disarm button. In this way, you will not arm the panel by 

mistake, which will not allow you to pair the next keyfobs before you disarm the panel.   

The learning mode lasts 30 seconds. If the receiver does not receive signal from the keyfob in the 
timeframe of 30 seconds, the pairing procedure will be terminated. The siren will beep 4 times to indicate 
an error.  

When a new keyfob is paired, the panel reports an event “Access Granted, User N” with ContactID E-422. 
Each keyfob reports with di erent user number (starting from 101). 

You need to repeat the pairing procedure for each additional keyfob.  

NOTE: 

To allow the panic button on the keyfob please refer to section 

“Con guring the panic button”.

 

Assigning a keyfob 

erent partition 

 

By default, the keyfob controls the  st partition after the pairing procedure. If there is a more than one 
partition set, you can set the keyfob to control a partition. To do that, log in the RControl Admin Portal, 
navigate to RControl Alarm menu, section Keyfobs and choose the desired Partition for each keyfob.  

NOTE: 

By default, each keyfob controls only one partition. If you want to control both partitions with a 

single keyfob, choose Partition=All for that keyfob in the RControl Admin portal. The buttons of the keyfob 
from the upper row will control Partition 1, the buttons from the lower row will control Partition 2. You will 
not be able to use Home Arm and Panic features of that keyfob.  

Summary of Contents for RControl-LA






















Reviews: