background image

 

8/17/11 

Rev.00 

Model  ........................................ 40M3L 
Frequency Range....................... 7.0-7.3 MHz X 150 kHz 
Gain............................................ 6.6 dBi 
Front to back .............................. 23 dB 
Beamwidth   ............................... E=62°  
Feed type ...................................Hair pin match 
Feed Impedance. ....................... 50 Ohms Unbalanced

 

Maximum VSWR........................ 1.3:1 typ. 2:1 max 
Input Connector.......................... SO-239, Other avl. 

Power Handling ..........................3 kW, Higher avl. 
Boom Length / Dia......................29.5’ / 3.0 x .125 Wall 
Element Length / Dia..................51 Ft 
Turning Radius: ..........................29 Ft 
Stacking Distance....................... Call 
Mast Size....................................2” to 3 ” Nom. 
Wind area / Survival ...................9.5 Sq. Ft. / 100 MPH 
Weight / Ship Wt.........................99 Lbs. / 125 Lbs. 
 

M2 Antenna Systems, Inc. 

Model No: 40M3L 

FEATURES: 

 

The 40M3L is a linear loaded 40 meter Yagi designed with 20 years of experience and listening to 

customer’s needs. The result is a powerful package of clean mechanical design, quality materials, and 
outstanding performance that will deliver years of enjoyment on the 40 meter band. 
 

Mechanically the elements are mounted between 

1/2” thick, 

machined aluminum clamp plates!  The 

Driven element is split and insulated with a 1-1/4 inch solid fiberglass rod and fed with a weather sealed 1:1 
balun.  All elements use linear loading of 3/16" 6061-T6 aluminum rod to reduce overall length, wind load, and 
turning radius. The linear loaded sections anchor 10" above the element to reduce inductive cancellation 
(requiring LESS loading), reduce mechanical stress, and minimize element droop (in the air the antenna is 
easily mistaken for a 15 or 20 meter Yagi!). Compare performance, construction and durability.... 

This is not 

just another 40 meter Yagi!!  

SPECIFICATIONS: 

*Subtract 2.14 from dBi for dBd

 

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722 

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com 

©2011 M2 Antenna Systems Incoporated 

 

Summary of Contents for 40M3L













Reviews: