background image

Changing Track Polarity Inside the Locomotive

Failing to properly configure the polarity will result in the locomotive starting in 
reverse instead of  forward or not receiving the DCS signal.  Should this occur, it is 
not necessary to swap the wires from the transformer to the track or reverse the 
locomotive’s orientation on the track itself.  Instead, simply slide the polarity 
switch located on the tender as seen in Figure 3.

DCS Polarity Switch

(The DCS Polarity Switch should be moved 
forward when the Red Terminal of the TIU is 
connected to the right hand rail and to the 
rear when the Red Terminal is connected to 
the left hand rail.)

H9 2-8-0 Steam Locomotive

4

Figure 3

Locomotive Coupler Options

Figure 5: Pre-drilled Kadee® Coupler mounting holes

The 2-rail locomotive models do not 
come with a rear coupler since many 
2-rail enthusiasts may utilize 
different coupler types on their 2-rail 
locomotives and cars.  Each tender 
has pre-drilled holes for use when 
installing a Kadee® scale coupler as 
seen in Figure 5.  Follow the 
individual coupler installation 
instructions when installing another 
manufacturer’s coupler system.

Summary of Contents for H9 2-8-0Steam Locomotive
































Reviews: