R9WTU-ED
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected]
EM-6225 Rev.1 P. 2 / 4
COMPONENT IDENTIFICATION
Terminal Block, Discrete Outputs
Output Status Indicator LED
Input Status Indicator LED
Terminal Block, Discrete inputs
COM COM
DI1 DI2
2
1
11
10
COM COM
DI3 DI4
4
3
13
12
COM COM
DI5 DI6
6
5
15
14
COM COM
DI7 DI8
8
7
17
16
NC
NC
9
18
NC DO8+
NC DO8-
8
9
17
18
DO7+ DO6+
DO7- DO6-
6
7
15
16
DO5+ DO4+
DO5- DO4-
4
5
13
14
DO3+ DO2+
DO3- DO2-
2
3
11
12
DO1+
DO1-
1
10
■
I/O STATUS INDICATOR LED
Discrete I/O extension units have LED indi-
cators showing I/O signal status.
Contact ON : LED ON
Contact OFF : LED OFF
TERMINAL ASSIGNMENTS
14
5
6
DI5
COM COM
15
DI6
16
17
18
7
8
9
DI7
DI8
NC
COM COM
10
1
2
DI1
COM COM
11
DI2
12
13
3
4
DI3
DI4
COM COM
NC
ID
ID
1
COM Input comon
10
DI1 Input 1ch
2
COM Input comon
11
DI2 Input 2ch
3
COM Input comon
12
DI3 Input 3ch
4
COM Input comon
13
DI4 Input 4ch
5
COM Input comon
14
DI5 Input 5ch
6
COM Input comon
15
DI6 Input 6ch
7
COM Input comon
16
DI7 Input 7ch
8
COM Input comon
17
DI8 Input 8ch
9
NC
Unused
18
NC Unused
■
DISCRETE INPUT
5
14
13
DO5–
DO5+ DO4+
4
DO4–
3
2
1
12
11
10
DO3– DO2– DO1–
DO3+ DO2+
9
18
17
NC
NC DO8+
8
DO8–
7
6
16
15
DO7– DO6–
DO7+ DO6+
DO1+
ID
ID
1
DO1– Output 1ch–
10 DO1+ Output 1ch+
2
DO2– Output 2ch–
11 DO2+ Output 2ch+
3
DO3– Output 3ch–
12 DO3+ Output 3ch+
4
DO4– Output 4ch–
13 DO4+ Output 4ch+
5
DO5– Output 5ch–
14 DO5+ Output 5ch+
6
DO6– Output 6ch–
15 DO6+ Output 6ch+
7
DO7– Output 7ch–
16 DO7+ Output 7ch+
8
DO8– Output 8ch–
17 DO8+ Output 8ch+
9
NC
Unused
18
NC Unused
■
DISCRETE OUTPUT
No.
FUNCTION
FUNCTION
FUNCTION
FUNCTION
No.
No.
No.
INSTALLATION
■
WALL MOUNTING
Insert the provided mounting adaptors into upper side of
the unit, and pull out those on the lower side. Fasten the
M4 screw to the hole (4.5 mm dia.) of each adaptor. (torque
1.4 N∙m)
To remove the adaptor, pull it out while squeezing the latch-
es as shown in the figure below.
push
push
■
DIN RAIL MOUNTING
Set the unit so that its mounting adaptors are at the bot-
tom. Position the upper hook at the rear side of the unit
on the DIN rail and push in the lower. When removing the
unit, push down the adaptors utilizing a minus screwdriver
and pull.
DIN Rail (35 mm wide)
Mounting Adaptor
