M-system R3-NL1 Instruction Manual Download Page 5

Page: 5 / 8

R3-NL1

P. 5 / 8

EM-8427 Rev.5

■

ANALOG INPUT FUNCTIONAL BLOCKS (GetValue [0] through [15])

GetValue [X]

nvoVal
SNVT_lev_percent
or SNVT_temp

or SNVT_state

cpNvoDefValue

cpNvoMaxRnge

cpNvoMinRnge

cpNvoSndDelta

cpNvoType

: (identical to nvoVal)

Default value at the startup

Span (full-scale) value

: (identical to nvoVal)

Zero value

: (identical to nvoVal)

Value deviation to be sent

: SCPTnvType

Network variable type, etc.

Configuration Properties

■

ANALOG OUTPUT FUNCTIONAL BLOCKS (SetValue [0] through [15])

SetValue [X]

cpNviDefValue

cpNviMaxRnge

cpNviMinRnge

cpNviType

: (identical to nviVal)

Default value at the startup

Span (full-scale) value

: (identical to nviVal)

Zero value

: SCPTnvType

Network variable type, etc.

Configuration Properties

nviVal
SNVT_lev_percent
or SNVT_state

■

DISCRETE INPUT FUNCTIONAL BLOCKS (R3Di [0] through [2])

R3Di [X]

nvoDich01
:
nvoDich16

SNVT_switch

nvoDiState

SNVT_state

Summary of Contents for R3-NL1









Search results

Summary of Contents for R3-NL1

Reviews:

Related manuals for R3-NL1

Brands by name

Popular brands

M-system R3-NL1, Instruction Manual

Search results

Summary of Contents for R3-NL1

Reviews:

Related manuals for R3-NL1

Brands by name

Popular brands