71VR1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected]
EM-7403-A Rev.7
P. 1 / 8
PAPERLESS RECORDER
(color LCD display)
MODEL
71VR1
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
This product is for use in general industrial environments,
therefore may not be suitable for applications which require
higher level of safety (e.g. safety or accident prevention sys-
tems) or of reliability (e.g. vehicle control or combustion con-
trol systems).
Make sure for safety that only qualified personnel perform
the wiring.
■
PACKAGE INCLUDES:
Paperless Recorder ....................................................... (1)
Installation fastener ............................................. (1) pair
CSJ sensor (for 71VR1- E501-x) .................................. (3)
■
MODEL NO.
Confirm that the model number described on the product is
exactly what you ordered.
■
INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
For detailed explanations to operate this product, please re-
fer to Model 71VR1 Operating Manual (EM-7403-B), down-
loadable at M-System’s web site.
http://www.m-system.co.jp
■
MEMORY CARD
Prepare the following model numbers:
Available for purchase from M-System. Consult M-System
• Manufacturer: Hagiwara Solutions
Model: NSD6-002GT (discontinued)
Capacity: 2 GB
• Manufacturer: Hagiwara Solutions
Model: NSDA-004GT (discontinued),
NSDA-004GL (discontinued),
NSD6-004GH
Capacity: 4 GB
• Manufacturer: Apacer Technology
Model: AP-ISD04GIS4B-T (discontinued), AP-ISD04GIS4B-3T
Capacity: 4 GB
POINTS OF CAUTION
■
CONFORMITY WITH EC DIRECTIVES
• This equipment is suitable for use in a Pollution Degree
2 environment and in Installation Category II, with the
maximum operating voltage of 300V.
Reinforced insulation is maintained between analog in-
put or contact input or contact output or network inter-
face, power and FE (Functional Earth), Basic insulation
is between analog input each other, contact input, contact
output each other and network interface. Prior to instal-
lation, check that the insulation class of this unit satisfies
the system requirements.
• Altitude up to 2000 meters.
• Do not share the grounding point of PE (Protective Earth)
of other devices with FE (Functional Earth). Handle as
signal ground.
• The equipment must be installed such that appropriate
clearance and creepage distances are maintained to con-
form to CE requirements. Failure to observe these re-
quirements may invalidate the CE conformance.
• In order to enable the operator to turn off the power input
immediately, install a switch or a circuit breaker accord-
ing to the relevant requirements in IEC 60947-1 and IEC
60947-3 and properly indicate it.
■
POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
Rating 100 – 240V AC: 85 – 264V, 50/60 Hz,
approx. 7VA at 100V, approx. 10VA at 240V
24V DC rating: 24V ±10%, approx. 6W
110V DC rating: 85 – 150V, approx. 6W
• Supplying any level of power other than specified above
will cause malfunctions.
• The power supply must have the startup characteristics
such that output voltage rises within operational voltage
range in 5 seconds.
• The power cables and the signal I/O cables must be lo
-
cated separately.
• The power cables, the signal I/O cables, and the commu
-
nication cables should not be bundled together or placed
near each other.
• To increase noise resistance of the power input wires,
twist the strands before connecting.
■
SAFETY PRECAUTION
• Before you remove the unit, turn off the power supply and
input signal for safety.
• Do not disassemble or modify the unit in any way. Doing
so may result in a fire or an electrical shock.
• Do not block the unit’s ventilation openings or use it in
areas where heat accumulates. Additionally, do not store
or use it under high-temperature conditions.
• Do not use the unit in an environment where flammable
gases or corrosive gases are present.
• Do not store or use the unit in locations subject to direct
sunlight, or where excessive dust or dirt is present.
• The unit is a precision instrument. Do not store or use it
where large shocks or excessive vibration can occur.
