manualshive.com logo in svg

M Design True Vision 1000 RD, Instructions For Installation And Use Manual, Page: 6 / 26

Share
Download
M Design True Vision 1000 RD Instructions For Installation And Use Manual Download Page 6

6

Small saucers provided 

with fireplace

Instructions for installation and use TRUE VISION 1000-1300RD Gas

3. Installing the fireplace

After having checked the appliance, you are ready to install your appliance. This is 

done as follows

3.1.1 Positioning the appliance

Place the appliance on a stable surface using the adjustable feet. Adjust the height of the 

appliance turning the bolt ( pic 1 )   

                      

Minimum and Maximum hight of the appliance :

Adjusting the height of the appliance Min 35mm to 450mm (floor to under the appliance). 
If you want the fireplace to be installed with a different height, unscrew the nut to remove the feet.
Grind the desired height on foot. The distance between two holes is 40mm. With the fireplace is provided 4 
small saucers. Use to get the stud under your feet.
If you want to install the fireplace at the minimum height of 25mm, measured from the floor to
Below the firebox: remove the foot and unscrew the nut below the foot. Aim the nut in
The tarred hole that is located below the hearth in the corner. Do the same for the four feet.
The minimum distance from the floor to the bottom of the frame is 244mm

The appliance must not be placed directly on the floor as you need to allow 
natural convection. The appertures for the air supply (IN) is situated 
underneath the appliances

Summary of Contents for True Vision 1000 RD



























Reviews:

No comments