manualshive.com logo in svg

M Design True Vision 1000 RD, Instructions For Installation And Use Manual, Page: 10 / 26

Share
Download
M Design True Vision 1000 RD Instructions For Installation And Use Manual Download Page 10

10

C

C

Instructions for installation and use TRUE VISION 1000-1300RD Gas

4.1. ROOF EXIT (C31)

 

The concentric flue duct should not be reduced to 150/100 for all True Vision.

Picture 1

4. Installing the chimney

Install the concentric flue duct as indicated by ONTOP - METALOTERM. The only authorised pipes are ONTOP 
Metaloterm™. ONTOP-METALOTERM tested our appliances with their conduct and we only guarantee a good 
working of the appliance with those. Between the external wall of the pipe and the wall or the ceiling, you 
should allow for a clearance of at least 50mm and protection that is suitable against temperatures of around 
130°C. The passage of the front panel cowl in the external wall must be filled in using silicone mastic.

Ø 200/130

Appliance

C  (min)

C  (max)

Restriction (as from 3m)

True Vision 1000 RD

2 m

10m

Ø 60

True Vision 1300 RD

2 m

10m

Ø 60

Summary of Contents for True Vision 1000 RD



























Reviews:

No comments