background image

Important Safety Instructions

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before 
the appliance is operated. 

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for 
future reference. 

3. HEED WARNINGS

All warning on the appliance and in the operating instructions 
should be adhered to. 

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed. 

5. WATER AND MOISTURE

The appliance should not be used near water – for example, 
near a bathtub, washbowl, kitchen sink, laundry tub, in a wet 
basement, or near a swimming pool, etc. 

6. CARTS AND STANDS

The appliance should be used only with 
a cart or stand that is recommended by 
the manufacturer. 

6A

. An appliance and cart combination 

should be moved with care. Quick 
stops, excessive force, and uneven 
surfaces may cause the appliance and 
cart combination to overturn. 

7. WALL OR CEILING MOUNTING

This equipment is not designed for use mounted on a wall or a 
ceiling. 

8. VENTILATION

The appliance should be situated so that its location or 
position does not interfere with its proper ventilation. For 
example, the appliance should not be situated on a bed, sofa, 
rug, or similar surface that may block the ventilation openings, 
or places in a built-in installation, such as bookcase or cabinet 
that may impede the flow of air through the ventilation 
openings. 

At least 30 cm free space around the unit for normal 
ventilation is required. 

9. HEAT

Do not install near any heat sources such as radiators, heat 
registers, stoves, or other apparatus (including amplifiers) that 
produce heat. 

10. CLEANING

The appliance should be cleaned only with dry cloth. 

11. POWER SOURCES

The appliance should be connected to a power supply only of 
the type described in the operating instructions or as marked 
on the appliance. 

12. POWER CORD PROTECTION

Power-supply cord should be routed so that they are not likely 
to be walked on or pinched by items placed upon or against 
them, playing particular attention to cords at plugs, 
convenience receptacles, and the point where they exit from 
the appliance. 

13. POLARIZED PLUG

Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than 
the other. A grounding type plug has two blades and a third 
grounding prong. The wide blade or the third prong are provided 
for your safety. When the provided plug does not fit into your 
outlet, consult an electrician for replacement of the obsolete 
outlet. 

14. UNPLUG POWER CORD

Unplug this apparatus during lightning storms or when unused 
for long periods of time. 

15. OBJECT AND LIQUID ENTRY

No object filled with liquids, such as vases, etc. shall be placed 
on the apparatus. 

16. ACCESSORIES

Only use attachments/accessories specified by the 
manufacturer. 

17. SERVICING

The user should not attempt to service the appliance beyond 
that described in the operating instructions. All other servicing 
should be referred to qualified service personnel. 

18. DAMAGE REQUIRING SERVICE

The appliance should be serviced by qualified service 
personnel when: 
a) The power-supply cord or the plug has been damaged; or
b) Objects have fallen, or liquid has been spilled into the 
appliance; or
c) The appliance has been exposed to rain; or
d) The appliance does not appear to operate normally or 
exhibits a marked change in performance; or
e) The appliance has been dropped, or the enclosure is 
damaged. 

Summary of Contents for DSM1































Reviews: