background image

Table of Contents

Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Features   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

What’s in the Box?   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Front and Back Panel Descriptions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setting up the 

Delta 1010-AI

with your Delta 1010   . . . . . . . . . . . . . . . . . . . . . . 4

Hooking Up Your ADAT Optical Device   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Using Your 

Delta 1010-AI

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ADAT to Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

ADAT to Analog Outs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Analog Ins to ADAT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

ADAT Thru . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mixed Modes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Standalone Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Master Clock Settings and the 

Delta 1010-AI

 . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Synchronizing your ADATs   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Limited Lifetime Warranty   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Delta 1010-AI

™ 

M A N U A L

Version 10AI 053100

Summary of Contents for DELTA 1010-AI













Reviews: