Lytx DC3P Installation Manual Download Page 4

 

 
 

© 2016 Lytx, Inc. – Confidential & Proprietary 

 

SAFETY INSTRUCTIONS  

Read and follow the instructions and precautions in this guide and all documents referenced in 
this guide when installing the DC3P event recorder (ER). Always refer to the vehicle manufacturer’s 
service manual for proper installation and wiring of any aftermarket devices, including the event 
recorder. Failure to do so may result in property damage and/or personal injury. 

WARNING:

 Always park the vehicle on a level surface before beginning any maintenance or 

installation.  Block the wheels to prevent the vehicle from moving.  Never work under the vehicle 
supported only by jacks.  Jacks can slip and fall over. 

WARNING:

 When you work on an electrical system, the possibility of electrical shock exists, and 

sparks can ignite flammable substances.  You must always disconnect the battery ground cable 
before you work on an electrical system to prevent serious personal injury and damage to 
components. 

EXPLOSION HAZARD:

 Do not disconnect equipment unless power has been removed or the area 

is known to be non-hazardous. 

WARNING:

 Substituting or supplementing components may impair suitability and performance.  If 

you are missing any components, contact Lytx, Inc. U.S. Technical Support Center at 866-910-0403 
or email 

[email protected]

WARNING:

 To prevent serious eye injury, always wear safe eye protection when you perform 

vehicle maintenance or service. 

Adherence to Applicable Local, State and Federal Laws 

WARNING:

 Some jurisdictions have adopted, or may in the future, adopt laws that may prohibit 

objects from being mounted on a vehicle’s windshield or other locations in a vehicle. You are 
responsible for complying with such laws, and Lytx, Inc. does not accept responsibility for your 
failure to do so. 

USA Federal Communications Commission (FCC) Notice 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation. 

Caution

: Changes or modifications to this product not expressly approved by Lytx, Inc. could void 

the user's authority to operate this equipment. 

Summary of Contents for DC3P





























Reviews: