background image

Lyngdorf Audio LS-1000 – Installation manual 

 

 

COMPLIANCE 

 
WEEE 

The European Parliament and the Council of the European Union have issued the Waste Electrical and 
Electronic Equipment Directive. The purpose of the Directive is to prevent waste of electrical and electronic 
equipment and to promote reuse, recycling, and other forms of waste recovery. Steinway Lyngdorf products 
and the accessories packed with them are subject to the WEEE Directive. Please dispose of any waste 
materials in accordance with your local recycling regulations. Products and equipment which must be 
collected for reuse, recycling, and other forms of recovery are marked with the icon of the crossed-out waste 
receptacle.  

 
 
 
 

 
FCC 

Steinway Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules. Operation is subject 
to the following two conditions: (1) this device may not cause harmful interference; and (2) this device must 
accept any interference received, including any interference that may cause undesired operation. Changes or 
modifications not expressly approved by the party responsible for compliance could void the user’s authority 
to operate the equipment. Equipment marketed to a consumer must be capable of complying with the 
necessary regulations in the configuration in which the equipment is marketed. 
 

 
 
 

 

 

 

Summary of Contents for LS-1000
















Reviews: