Luxul Xen XAP-1040 User Manual Download Page 28 | Manualshive

Page: 28 / 32

background image

User Guide

28

© Copyright 2014 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.

5.7 Status

5.7.1 Basic Status

Basic Status:

This page displays basic setup information of the confi guration and

status of the AP including: Firmware Version, Hardware Model, Uptime, Connection
Type, IP Address, Subnet Mask, Default Gateway, LAN MAC Address, Wireless
Mode, Wireless MAC Address, Network Name (SSID), Channel Width, Channel, and
type of Security

5.7.2 Connected Clients

Connected Clients:

This page displays the MAC Address, Speed and Signal Strength

of all currently attached wireless devices.

«
...
26
27
28
29
30
...
»

Summary of Contents for Xen XAP-1040

































Reviews:

No comments

Related manuals for Xen XAP-1040

Brand: Airlink101 Pages: 7

Brand: NC-link Pages: 13

Brand: Rawafed Libya Pages: 22

Skyr@cer WBR 354G

Brand: Topcom Pages: 104

Brand: SENAO Pages: 2

Brand: SWEEX Pages: 8

Brand: SWEEX Pages: 32

Brand: IP-COM Pages: 15

Brand: IP-COM Pages: 63

Brand: P2 MOBILE TECHNOLOGIES LIMITED Pages: 5

Portfolio GSM0400 Series

Brand: Enfora Pages: 23

Cinterion ENS22-E

Brand: Gemalto Pages: 189

Brand: Link Play Pages: 24

Brand: Ebyte Pages: 30

Fritz!Box 6850 LTE

Brand: Fritz! Pages: 257

Brand: Ebyte Pages: 22

3CRWE554G72T - OfficeConnect Wireless 11g Cable/DSL...

Brand: 3Com Pages: 146

Brand: Planet Networking & Communication Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands